HP 600n Print Server for Token Ring manual Link Configuration Jumper Settings, Jumper Location

Page 44

Link Configuration Jumper Settings

Link configuration jumpers (P1, P2, and P3) can be used to configure the card. These jumpers should be used if the card is unable to establish a network link through autonegotiation. If P1 is changed to the AUTO=OFF position, then P2 selects the link speed (10 or 100 Mbps) and P3 selects the communication mode (Half duplex or Full duplex). If you manually configure the card using jumpers P2 and P3, you must match the configuration of the connecting device, such as the network hub or switch.

Jumper Setting Descriptions

AUTO = ON (Default)*

100 Mbps

Half-Duplex

(AUTO = OFF)

100 Mbps

Full-Duplex

(AUTO = OFF)

10 Mbps

Half-Duplex

(AUTO = OFF)

10 Mbps

Full-Duplex

(AUTO = OFF)

Jumper Location

(*Note: If the jumper on P1 is removed or lost, the card defaults to the AUTO=ON state.)

A-2 HP J3113A 10/100Base-TX Print Server

Image 44

Contents HP JetDirect 600N Hardware Installation Guide Page Hardware Installation Guide HP JetDirect 600N Print Server Publication number Quick Installation Identify Your HP JetDirect 600N Internal Print ServerHP J3110A for Ethernet 10Base-T networks HP J3112A for Token Ring Ieee 802.5 networksIf Necessary, Set Switches or Jumpers on Your Card Before Installing the Card, Verify That Your Printer WorksPrint a Printer Configuration If You Have a Token Ring CardTurn on the printer and print another configuration Verify That the Card Is Operating ProperlyConfigure the Card for Network Operation Table of Contents Using the Embedded Web Server Introduction Supported Network Protocols TCP/IPSupported Printers IntroductionIntroduction Installing the Print Server What You Need for Installation Identify Your HP JetDirect 600N Internal Print Server You can use only one Token Ring port RJ-45 or DB If Necessary, Set Switches or Jumpers on Your Card 10/100 Half/Full AutonegotiationBefore Installing the Card, Verify That Your Printer Works HP LaserJet Printers and MopiersService Config HP DesignJet PrintersTypical Card Installation and Network Connection Turn Off Your Printer and Insert the CardVerify That the Card Was Installed Correctly For HP J3113A 10/100Base-TX cards See For LocalTalk-Only Customers If you areConfigure the Card for Network Operation HP JetDirect Administrator’s Guide provided on Installing the Print Server Control Panel Configuration Introduction To Restore Configuration Default Values To Enable or Disable Network ProtocolsTo enable or disable network protocols Press Select. CFG NETWORK=YES* appearsConfiguring IPX Frame Types IPX Frame Types on an HP JetDirect Ethernet CardIPX Frame Types on an HP JetDirect Token Ring Card Frame Type DescriptionTo configure an IPX frame type CFG IPX/SPX=NO* is displayedSource Routing Description Configuring IPX Source Routing Token Ring Cards OnlyTo configure IPX source routing Press Item until SRC RC=Source Routing* appears Configuring TCP/IP Parameters Parameter DescriptionTo configure TCP/IP parameters CFG TCP/IP=NO* is displayed CFG ETALK=NO* is displayed To configure EtherTalk parametersPress Item. Etalk PHASE=1* or Etalk PHASE=2* appears Control Panel Configuration Using the Embedded Web Server HP Web JetAdmin Compatibility Supported Web BrowsersViewing the Embedded Web Server Embedded Web ServerOperating Notes LED State Description Off Not linked HP J3113A 10/100Base-TX Print Server Supported LinksLink-Speed LEDs Jumper Location Link Configuration Jumper SettingsJumper Setting Descriptions Link Troubleshooting Parameter Expected Messages for 10/100TX CardsHP J3113A 10/100Base-TX Print Server Specifications and Regulatory Statements HP JetDirect 600N Internal Print ServerElectrical EnvironmentalFCC Statements Regulatory StatementsElectromagnetic Specifications Regulatory European CommunitySpecifications and Regulatory Statements Vcci Class a Japan RRL Statement Korea Taiwan Class a AustraliaCanada Chinese Safety Statement Page 5969-3561