GE 2800 manual Power Connection Kits, Zoneline Chassis Nomenclature, Example

Power Connection Kits

230/208-Volt Line Cord Connection Units

Line Cord	Electric	Electric	Electric	Min. Circuit
	Heat	Heater	Heat	Protection
Kit
	BTUH	Watts	Amps	(Amps)
RAK3153	8600/7100	2550/2090	11.6/10.6	15
RAK3203	11700/9600	3450/2820	15.5/14.1	20
RAK3303	170100/13900	5000/4090	22.3/20.3	30

Electric Heat Amps include electric heater and fan motor current draw.

Each Line Cord Kit has an integral Leakage Current Detection and Interruption (LCDI) or Arc Fault Current Interrupter (AFCI) device as required by National Electrical Code (NEC) and Underwriters Laboratories (UL) for units manufactured after August 1, 2004.

ge.com

230/208-Volt Sub-Base and Direct Connected Units

	Direct	Electric	Electric	Electric	Min. Circuit
Sub-Base	Connection	Heat	Heater	Heat	Protection
	Kit	BTUH	Watts	Amps	(Amps)
RAK204D15P	RAK4157	8600/7100	2550/2090	11.6/10.6	15
RAK204D20P	RAK4207	11700/9600	3450/2820	15.5/14.1	20
RAK204D30P	RAK4307	170100/13900	5000/4090	22.3/20.3	30

Electric Heat Amps include electric heater and fan motor current draw.

Units connected through sub-base do not require a LCDI or AFCI device since they are not considered to be line-cord connected. Each 230/208-volt sub-base kit consists of sub-base with appropriate receptacle for minimum circuit amperage, chaseway to route power connector from sub-base to chassis, wiring to connect sub-base to building wiring and a short line cord with 9-pin connector to connect to chassis and plug into receptacle in sub-base.

Short sub-base line cord may not be used without sub-base. Junction box for 230/208-volt chassis must be purchased separately. RAK4002A for 2800 and 3800 series units RAK4002B for 5800 series units.

265-Volt Sub-Base and Direct Connected Units

Sub-Base	Power	Direct	Electric Heat	Electric Heater	Electric Heat	Min. Circuit Protection
	Connection Kit	Connection Kit	BTUH	Watts	Amps	(Amps)
RAK204E15	RAK5172	RAK5157	8600	2550	9.6	15
RAK204E20	RAK5202	RAK5207	11700	3450	13.0	20
RAK204E30	RAK5302	RAK5307	17000	5000	18.9	30

Electric Heat Amps include electric heater and fan motor current draw.

265-volt units are to be permanently connected in compliance with National Electrical Code and local codes and have a factory-installed junction box on the chassis. Each 265-volt sub-base kit consists of sub-base with appropriate receptacle for minimum circuit amperage, chaseway to route power connector from sub-base to chassis and wiring to connect sub-base to building wiring.

265-Volt Power Connection Kit must be ordered separately.

Important

Essential Elements Ordering Overview

230/208-volt line cord connected units — order line cord kit 230/208-volt sub-base connected units — order sub-base and junction box 265-volt units — order sub-base and power connection kit

Zoneline® Chassis Nomenclature

The Zoneline chassis is identified by a model number defining the type of unit, cooling capacity, electrical information and optional features included on the unit. When specifying or ordering the Zoneline chassis, the use of this nomenclature will assure receiving the correct unit.

EXAMPLE

A	Z	5	8	H		1	2	D		A	D
Zoneline		Chassis series			Nominal cooling capacity				Universal
packaged		28=deluxe line cool/			07=7,000 BTUH cooling				power connection
terminal		electric heat			09=9,000 BTUH cooling
chassis		38=deluxe line heat pump			12=12,000 BTUH cooling				Special Features
		58=premium line			15=15,000 BTUH cooling				B=base unit
		heat pump							C=corrosiontreated
						Voltage/Phase/			D=internal
		Unit type				Frequency				condensate
		E=cooling with electric				D=230/208-Volt,				removal (ICR)
		resistance heat				single-phase, 60 Hz				system (heat
		H=heat pump with electric				E=265-Volt, single-phase,				pump models
		resistance heat				60 Hz				only) (not for
										coastal areas)
									P=Dry Air 25 (2800
										Series only)