APC ACPA4000 manual Start-Up, Start-upchecklist, How to apply power to the equipment

Page 23

Start-Up

Start-Up

Start-up checklist

Before starting the equipment, check to see that the following conditions are met:

•All electrical connections comply with national and local codes and safety standards.

•All accessories and ductwork have been installed.

•Air flow to and from the equipment is not blocked.

•The condensate drain is connected and not kinked or pinched.

How to apply power to the equipment

	Insert the IEC-320-C19 connector of the power	Circuit breaker
	cord into the back of the equipment. Insert the	Circuit breaker
	cord into the back of the equipment. Insert the
	opposite end of the power cord, a NEMA 5-20
	plug, into the wall outlet. Verify the circuit
	breaker is pressed in (flush with the rear of the
	equipment), and the green LED on the back of
	the plug is on.

Electrical Hazard: Do not use extension cords with this equipment. Using an extention cord reduces circuit protection and voids the warranty.

Note: If the equipment has been unplugged or off for less than three minutes, it waits three minutes before starting the compressor.

Warning: Route the power cord and the condensate line to prevent accidental injury to people or damage to the equipment.

NetworkAIR ACPA4000

15

Image 23

Contents NetworkAIR Portable Air Conditioning Unit ACPA4000Installation, Operation, and Maintenance Page American Power Conversion Legal Disclaimer Page Contents InstallationGeneral Information Operation Maintenance and Troubleshooting Page About the NetworkAIR ACPA4000 General InformationOverview Manual updatesCross-referencesymbol used in this manual Safety symbols that may be used in this manualFiling a claim Storing the Equipment Before InstallationInspecting the Equipment SafetyThe equipment ships with the items shown below Tools RequiredInventory Rear view Component IdentificationFront view Shipping Weight Dimensions and WeightsDimensions are shown in mm in Net WeightLock the rolling casters InstallationWhere to locate the equipment Assemble the ceiling adapter Intake and Exhaust VentsHose connections NetworkAIR ACPA4000 Install the adapter in a drop ceilingAssemble the ducts Attach the drain line. Attach Drain LineConnect the fitting to the drain line Temperature/humidity sensor AccessoriesOutput relays Relays and ContactsOverview To connect an input contact Input contactsTo connect an output relay How to apply power to the equipment Start-UpStart-upchecklist Display interface identification OperationOverview Scrolling status screens How to Use the InterfaceTurn on the equipment Date 18-Jun-2007 Time Main menu screenNavigating the interface Date 18-Jun-2007 TimeTurn off the equipment Change settingsPassword entry Default schedule Set Environmental ControlsMode Operating schedulesSchedule 1 of Schedule On/OffSet the alarm delay Set Up AlarmsTemperature and humidity alarms Display interface options Set Up the DisplayPassword and time-out Set the date and timePath Main Menu Setup Factory Defaults Device settingsResetting to default settings Path Main Menu Setup System DeviceHow to download firmware User outputs Set Up Contacts and RelaysInput contacts User input contactsSystem and environmental status screens Checking Equipment StatusDefault schedule status Scrolling status screensManufacturer data Viewing alarm statusWarning or alarm LED Responding to AlarmsSilencing the alarm beeper Silence Active AlarmResolving alarm conditions Active alarm screenAlarm and event log Action Required Alarm messagesAlarm Message Remote temperature Alarm MessageAction Required Monitoring information Display Interface Reference ChartsSetup Scrolling status screensControl Environment Programmable settingsSetup StatusSystem SetupReplace the air filter Maintenance and TroubleshootingMaintenance Update the main control board firmware Clean the condenser filter and test the LCDI plugClean the cabinet Corrective action TroubleshootingProblem Possible causeExclusions One-YearFactory WarrantyTerms of warranty Non-transferablewarrantyWarranty claims Parts Warranty ProceduresClaims Component Type SpecificationsElectrical PhysicalPage 03/2008 990-0412DAPC Worldwide Customer Support 990-0412D