(b)Display sequence of error, inspection display lamp
1)One kind error
Display corresponding to the error is shown.
2)More than one errors.
Section |
| Display section | |
|
| ||
Error code of remote controller | • Displays the error of higher priority (When plural errors are persisting) | ||
| ··········· | ··········· | |
Inspection LED (red) of indoor unit PCB | |||
|
| ||
| • Displays the present errors. |
| |
Inspection LED (red) of outdoor unit PCB |
| ||
(When a new error has occurred after the former error was reset.) | |||
|
|
| |
3)Timing of error detection
● Indoor unit side.
Error detail |
|
|
| Error code |
| Timing of error detection | |||||
|
|
|
|
|
|
|
|
|
|
|
|
Drain error (float switch motion) |
|
|
|
|
|
|
|
|
| Normally, 30 seconds after the power is turned ON. | |
|
|
|
|
|
|
|
|
|
|
|
|
Wrong connection between the indoor and | “ |
|
|
| Wait |
|
|
| ” | No communications even once with the outdoor unit. | |
outdoor units. |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Transmission error of remote controller |
|
|
|
|
|
|
|
|
| After 1 or more communications of the indoor unit with the remote controller | |
indoor unit |
|
|
|
|
|
|
|
|
| following power on, transmission errors cause an interruption for 2 minutes. | |
|
|
|
|
|
|
|
|
|
|
| |
Transmission error between indoor/outdoor |
|
|
|
|
|
|
|
|
| After communications with the outdoor unit 1 or more times, communications | |
units |
|
|
|
|
|
|
|
|
| are abnormal continuously for 2 minutes. | |
|
|
|
|
|
|
|
|
|
|
|
|
The number of connected indoor units |
|
|
|
|
|
|
|
|
|
|
|
exceeds the connection limit (when |
|
|
|
|
|
|
|
|
| Normally after the power is turned ON (during communications). | |
multiple units are control by a single remote |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |
controller). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Broken wire of indoor unit return air |
|
|
|
|
|
|
|
|
| When an input temperature of | |
|
|
|
|
|
|
|
|
| thermistor is measured for 5 seconds or longer within 60 minutes after the | ||
thermistor |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| first detection. | ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |
Broken wire of heat exchanger thermistor |
|
|
|
|
|
|
|
|
| When an input temperature of | |
|
|
|
|
|
|
|
|
| exchanger thermistor is measured for 5 seconds or longer within 60 minutes | ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| after the first detection. | |
●Outdoor unit side.
Error detail | Error code | Timing of error detection |
|
|
|
|
| When a thermistor input temperature of |
Broken wire of outdoor air temperature |
| seconds or longer 3 times within 40 (60) minutes after the 1st detection |
thermistor |
| between 2 minutes and 2 minutes 20 seconds after compressor operation |
|
| starts. |
|
|
|
Broken wire of heat exchanger thermister |
| When a thermistor input temperature of |
| seconds or longer 3 times within 40 (60) minutes after the 1st detection | |
|
| between 2 minutes and 2 minutes 20 seconds after compressor operation |
|
| starts. |
Broken wire of discharge pipe thermistor |
| When a thermistor input temperature of |
| seconds or longer 3 times within 40 (60) minutes after the 1st detection | |
|
| |
|
| between 10 minutes and 10 minutes 20 seconds (between 2 minutes and 2 |
|
| minutes 20 seconds) after compressor operation starts. |
|
|
|
Broken wire of power transistor |
| When the |
| 5 seconds or longer 3 times within 40 minutes after the 1st detection between | |
thermistor |
| 10 minutes and 10 minutes 20 seconds after compressor operation starts. |
|
|
|
Notes (1) Values in ( ) show for the FDCA301~601 models.
(2) The power transistor temperature sensor is used in the FDCVA151~251 models only.
- 6 -