Hunter Fan R410A manual Error display e40 63H1 operation Only case of 301~601 type

Page 32

10

Error display : e40 [63H1 operation] (Only case of 301~601 type)

 

Indoor unit

 

Outdoor unit

Red LED

 

Stays OFF

Red LED

 

1 time flash

Green LED

 

Keeps flashing

Green LED

 

Keeps flashing

Is the 63H1 operating?

NO

YES

While the 63H1 is operating

1.During Cooling

Is the outdoor unit fan motor running?

Is there a short circuit in the outdoor unit?

Is there enough space for inlet and outlet?

2. During Heating

Is the indoor unit heat exchanger thermistor separated

from the sensing case?

Is the filter clogged?

The outdoor unit control PCB

is faulty. (The 63H1 input circuit is faulty.) Replace

3. During Cooling and Heating

Is the refrigerant overcharge?

Is the service valve fully open?

[Open phase at L3-phase of 52C primary side]

 

Indoor unit

 

Outdoor unit

Red LED

 

Stays OFF

Red LED

 

1 time flash

Green LED

 

Keeps flashing

Green LED

 

Keeps flashing

 

 

52C

(1)

YES

primary side L3 phase

 

 

 

Repair

 

 

open?

 

 

Notes (1) Also check if there is voltage at the L3 phase on the 52C primary

 

 

NO

 

 

side, but no voltage on the secondary side (coil wire disconnection

 

 

 

(2)

 

 

 

 

 

or faulty contacts).

The outdoor unit control PCB

 

 

(2) If there is voltage at the L3 phase on the 52C primary side and it is

is faulty.

 

Replace

 

 

not abnormal, the outdoor unit control PCB is faulty.

 

 

 

 

 

 

 

 

11

Error display : e42 [Current cut] (Only case of 151~251 type)

 

Indoor unit

 

Outdoor unit

Red LED

 

Stays OFF

Red LED

 

1 time flash

Green LED

 

Keeps flashing

 

 

 

Is the power

supply voltage

proper?

NO

Check the power supply.

YES

 

Is the service

YES

 

valve fully open?

 

 

 

NO

 

 

 

 

 

 

 

 

Open it fully.

 

 

 

 

 

 

 

Is the high

YES

pressure during operation

 

proper?

 

NO

Check the refrigerant level and refrigerant circuit.

Check the compressor's insulation YES resistance and winding

resistance.

NO

Replace the compressor.

Display conditions

If the inverter’s output current ex-

Check the

 

 

NG

ceeds the set value, the compres-

power transistor module

 

sor stops. After a 3-minute delay, it

(See page 160)

 

 

 

restarts, but if this occurs 3 times

OK

 

within 20 minutes.

 

Is the installation space for the indoor and outdoor

YES

units proper?

 

Is there a short circuit in the indoor or outdoor units?

During cooling: Is FMo operating?

Is the service valve fully open?

During heating: Is FMI operating?

Replace the outdoor unit control PCB.

Does it return to

normal if the power NO supply is reset

(2 of 3 times)?

YES

Replace the outdoor unit control PCB.

Is the service valve fully open?

Is the filter clogged?

Is liquid flowing back to the compressor?

Is the compressor making abnormal noises?

It may be malfunction due to transient noise. If there is a noise source nearby, take measures to eliminate it.

- 30 -

Image 32
Contents FDA Series Split Systems FDA Series Multi Systems Page Index Evacuation procedure EvacuationRefrigerant charging High side Low sideIndi Cation CircuitSelfdiagnosis function Check Indicator Table Indoor unit sideNo-indication E10 E16 E28 Indoor unit LED Outdoor unit LEDOutdoor unit side Wait Display sequence of error, inspection display lampTiming of error detection Recording and reset of error Procedures of trouble diagnosisError diagnosis procedures at the indoor unit side Indoor unit Outdoor unitParts layout on the indoor unit PCB Model FDT series Change by the jumper wireControl change switch SW5, SW9, SW10 Model Fden series Model Fdkn series Model Fdur series Drain motorCheck method when the error code is display Indoor unit Outdoor unitRemote controller wire Is removed Replacement indoor Unit control PCBRed LED Time flash Stays OFF Green LED Keeps flashing Approximately301~601 151~251Red LED Only case of FDT Cases of other than FDTRed LED Stays OFF Green LED Stays OFF or LightsDefective indoor unit heat exchanger thermistor Error display e6Error display Detective return air thermistor Error display Heating overload Abnormal Temperature DetectionError display Drain trouble Indoor unit heat exchanger temp. ˚CError display Error display e16 Fan motor abnormalitiesE10 Only case of FDTA501, 601 typesOnly case of Fdkn Only case of 151~251 types Display conditionsWithin a period of 1 hour Only case of 301 typeError display e28 Directive remote controller thermistor Are characteristicsDetectivie remote controller PCB Remote controller therm Replacement Detective reError diagnosis procedures at the outdoor units side Change by the jumper wire Function of DIP switches SW5 Usually all turned OFFParts layout on the outdoor unit PCB FDCVA151~251 type Change by the JA3Overcurrent Setting FDCA301~601 typePower transistor module E32 Error display Communications error during operationPower supply phases reversed Only case of 301~601 type Compressor overcurrent trouble Only case of 301~601 type E33Inverter primary current abnormal Only case of 151~251 type Error display e35 Cooling overload operation E34Pressor is stopped Error display e36 Discharge temperature errorAbnormal Temperature Detection Error display e39 Defective discharge pipe thermistor Utes100 80 CError display e42 Current cut Only case of 151~251 type Error display e40 63H1 operation Only case of 301~601 typeOpen phase at L3-phase of 52C primary side Error display e52 52C Abnormal Only case of 301~601 type E47E48 Inverter over-voltage trouble Only case of 151~251 typeInsufficient refrigerant volume E57Did it improve? Replacement Compressor Could be causingRefrigerant circuit Malfunction. IfPower transistor module including drive circuit check method Is the powerCheck abnormal operation data with the remote controller Remote controller Wired remote controller Pull the cover downward to open itRemote controller unit functions Indoor unit functions I/U FunctionFunction setting method When Function is selectedWhen I/U Function is selected Press the ON/OFF buttonChanging the remote controller’s temperature setting range Cooling Test Operation Procedure Canceling the Cooling Test OperationStarting the Cooling Test Operation Checking Operation DataSetting SW5-1, SW5-2 on-site Test run Test run methodChecking the state of the unit in operation HeatingIndication board Fden Series Fdkn SeriesWireless remote controller Page Installation of this equipment must comply with all NATIONAL, State and Local Codes