Enviro owner manual Install the Wired Sensors, EA800 Base Unit Power Connections

Page 26
Install the Wired Sensors

Install the Wired Sensors

2.Mount the mounting plate as follows:

■Mounting to 3-gang enclosure: Use four (4) machine screws to secure the mounting plate to the mating holes in the 3-gang enclosure.

■Mounting to drywall surface: Place the mounting plate in mounting position. Mark the four mounting hole locations. Install drywall anchors and secure the mounting plate to the anchors.

Note: If wall-mounted, prepare a wiring access hole at this time. All wiring must pass through the opening in the center of mounting plate.

Install the Wired Sensors

Install the wired sensors in accordance with the instructions provided with the wired sensors.

1.Mount each wired sensor in its designated location.

2.Label each sensor's wires for easy identification.

3.Route the wires from the sensor to the base unit and dress the wires as required by local code. It is important to ensure that the wires are protected along their entire length, are not stressed at any point, and are adequately supported along their entire length.

4.Pass the wires through the mounted EA800 rear panel.

EA800 Base Unit Power Connections

!CAUTION

!CAUTION

Do not connect or disconnect power, sensor, or alarm wiring while power is applied. Connecting and disconnecting the EA800 base unit with power connected may damage the base unit or result in improper or unreliable operation.

Connection of unsuitable loads to this connection may damage the power supply and EA800 base unit, or result in improper or unreliable operation.

Note: Do not apply power to the base unit until you are ready to begin sensor programming. The base unit has a 30-minute timer that starts when the unit is first powered up. If at least one sensor is not added and pro- grammed within the 30-minute time period, an alarm will occur.

1.Using a terminal block adapter, connect power supply + and - leads to POWER IN (+) and (-) on J5. Observe proper polarity. If using a transformer, ensure that the transformer is an isolated power supply.

2.If Aux Power Out is to be used, connect + and - leads to AUX POWER OUT (+) and (-) on J5 using a terminal block adapter.

Install the Wireless Sensors

 

 

If the EA800 base unit will be connected to a remote alarm panel, do not connect

!

CAUTION

the base unit to the alarm panel until after sensor connection and configuration

 

 

 

 

is complete. Connecting the remote alarm panel before configuring the EA800

 

 

sensors will result in false alarms at the remote panel.

22

D-011-0152

Page 25 Page 27
Image 26
Page 25 Page 27
Contents D-011-0152 Limitations of the Alarm System or Device General Information Table of ContentsInstallation PreparationOperation General Information OverviewHow to Use This Manual D-011-0152 Block DiagramsGeneral Information Symbols on the Product or Manual Labeling D-011-0152 Monitoring ScreensGeneral Information Keys Base Unit Connections Access Control and Passwords selected System Configuration Parameterswill sound when an alarm occurs if DISABLE is Sensors Temperature SensorsTheory of Operation Humidity Sensors4-20mASensors Power Supply / Sensor Voltage Selection Contact Closure Sensors Water SensorsMulti-FunctionSensors Maximum Allowed Sensor Parameter DescriptionsResolution High Scaled ValueRelay Operation Relay Operation D-011-0152Preparation D-011-0152 loop circuit power supplied via loop From 11-26VDC power supplyTo alarm-on-closed From 11-26VDC power supplyD-011-0152 Tools and Supplies Required InstallationPower Requirements Mounting the EA800 Rear PlateInstall the Wireless Sensors Install the Wired SensorsEA800 Base Unit Power Connections RESET BUTTON SENSOR MODEL NOD-011-0152 RESET BUTTONSENSOR MODEL NO J6 Input 1 Input 2 Input 3 InputConnecting Wired HA-III+Humidity Sensors Connecting Wired 4-20mASensors Connecting the EA800 Alarm Outputs ProgrammingAccessing the MAIN MENU for Programming Configuring System Parameter Settings3.Enter the SYSTEM menu and then select the CONFIGURATION menu as shown below DISABLED is selected Setting the Current Date Setting the Time D-011-0152Adding Wireless Sensors Adding a Wireless Temperature SensorAdding Wireless Sensors D-011-0152Installation D-011-0152D-011-0152 D-011-0152 Adding a Wireless Humidity SensorInstallation D-011-0152 Installation D-011-0152D-011-0152 D-011-0152 InstallationSelect N.O. Contact or N.C. Contact Verify Wireless Signal Strength D-011-0152Adding Wired Sensors Adding a Wired Temperature SensorD-011-0152 Adding a Wired HA-III+Humidity SensorAdding Wired Sensors Adding a Wired WaterBug Sensor Note A supervised WaterBug sensor must be usedD-011-0152 Adding a Wired Contact Closure SensorSelect N.O. Contact or N.C. Contact Adding a 4-20mASensor Configuring the Relays Operation Monitoring Environmental ConditionsViewing Sensor Settings Viewing Active AlarmsViewing the Alarm Log Viewing Pending Alarm InformationViewing Limit Settings Viewing the Event LogOperation Viewing the Sensor LogViewing Firmware Information D-011-0152Viewing RF Information Viewing RF InformationMaintenance Locking and Unlocking the EA800Pausing Monitoring and Cancelling Pause Adding a Sensor Replacing a SensorEditing Sensor Parameters SENSORS screenF3 F3 Reprogramming a RelayDeleting a Sensor Changing the Date Format Changing the Time FormatChanging the Date or Time Setting Changing Sensor Data Collection FrequencyChanging the Buzzer Setting Changing the Buzzer SettingD-011-0152 Changing the PasswordMaintenance Clearing the Alarm Log Clearing the Alarm LogClearing the Sensor Log D-011-0152 Updating the FirmwareMaintenance Saving Configuration Settings F3 LOAD/SAVE CONFIG screenLoading Configuration Settings CONFIG screenExported Alarm Data Exporting the Stored Logs12/24/2007 07 06 03 PM Exported Event DataExported Sensor Data Sensor deletedExporting the Stored Logs D-011-0152Troubleshooting ACTIVE ALARMS screenVerifying RF Signal Strength Viewing Signal Strength for a Wireless SensorSpecifications Base Unit and Sensor SpecificationsAccessories Appendix A Screen Maps Figure 17. Locked Screen MapFigure 18. Unlocked Screen Map - Top Level D-011-0152D-011-0152 Appendix A Screen MapsFigure 19. Sensors Screen Map Figure 20. Add New Sensor Screen Map D-011-0152Figure 22. Relay Screen Map Appendix A Screen MapsFigure 21. Edit Sensor Screen Map D-011-0152Figure 23. Data Log Screen Map D-011-0152D-011-0152 Appendix A Screen MapsFigure 24. System Screen Map Figure 25. Configuration Screen Map D-011-0152Alarm Condition Appendix B Planning WorksheetInstallation Appendix B Planning WorksheetD-011-0152 C Wiring Diagram AppendixD-011-0152 Appendix D System Configuration Record Unit of Measure Appendix D System Configuration Record Sensor 6 Settings wireless Appendix D System Configuration Record D-011-0152 Warranty and Service Information 1950 Excel Drive, Mankato, MN, Outside MN Phone Manufactured in the U.S.A byWinland Electronics Phone Fax
Top Page Image Contents