Enviro EA800 owner manual Adding Wireless Sensors, Adding a Wireless Temperature Sensor

Page 37
Adding Wireless Sensors

Installation

Adding Wireless Sensors

Go to the appropriate section for the wireless sensor to be added:

■Wireless Temperature Sensor: See “Adding a Wireless Temperature Sensor” on page 33

■Wireless Humidity Sensor: See “Adding a Wireless Humidity Sensor” on page 37

■Wireless Multi-Function Sensor: See “Adding a Wireless Multi-Function Sensor Using a Wired Temperature Sensor” on page 35. Multi-function sensor may be programmed to operate with the following types of wired sensors:

•Low Temperature Sensor - Blue Thermistor Probes: See “Adding a Wireless Multi-Function Sensor Using a Wired Temperature Sensor” on page 35.

•High Temperature Sensor - Red Thermistor Probes: See “Adding a Wireless Multi-Function Sensor Using a Wired Temperature Sensor” on page 35.

•Ultra Low Temperature Sensor - White Thermistor Probes: See “Adding a Wireless Multi-Function Sensor Using a Wired Temperature Sensor” on page 35.

•WaterBug Sensor: See “Adding a Wireless Multi-Function Sensor Using a Wired WaterBug Sensor” on page 38.

•N.O. Contact: See “Adding a Wireless Multi-Function Sensor Using a Wired Contact Closure Sensor” on page 40.

•N.C. Contact: See “Adding a Wireless Multi-Function Sensor Using a Wired Contact Closure Sensor” on page 40.

 

 

If the EA800 base unit will be connected to a remote alarm panel, do not connect

!

CAUTION

the base unit to the alarm panel until after sensor connection and configuration

 

 

 

 

is complete. Connecting the remote alarm panel before configuring the EA800

 

 

sensors will result in false alarms at the remote panel.

Adding a Wireless Temperature Sensor

1.Unlock the base unit if necessary to continue programming. See “Accessing the MAIN MENU for Programming” on page 28.

2.Select SENSORS from the MAIN MENU and follow the steps in the following diagram.

3.After you press the ENTER key, the NEW WIRELESS SENSOR screen is displayed. The EA800 searches for new wireless sensors, indicated by an arrow that moves from left to right across the screen. When an available wireless sensor has been detected, it is listed in the SELECT SENSOR screen as shown below.

4.Confirm that all new (unprogrammed) wireless sensors are displayed on the SELECT SENSOR screen, use the arrow keys to select the sensor to be configured, then follow the prompts to configure all screens for that sensor.

D-011-0152

33

Page 36 Page 38
Image 37
Page 36 Page 38
Contents D-011-0152 Limitations of the Alarm System or Device Installation Table of ContentsGeneral Information PreparationOperation Overview General InformationHow to Use This Manual General Information Block DiagramsD-011-0152 Symbols on the Product or Manual Labeling General Information Monitoring ScreensD-011-0152 Keys Base Unit Connections Access Control and Passwords will sound when an alarm occurs if DISABLE is System Configuration Parametersselected Temperature Sensors Sensors4-20mASensors Humidity SensorsTheory of Operation Power Supply / Sensor Voltage Selection Multi-FunctionSensors Water SensorsContact Closure Sensors Resolution Sensor Parameter DescriptionsMaximum Allowed High Scaled ValueRelay Operation D-011-0152 Relay OperationPreparation D-011-0152 To alarm-on-closed From 11-26VDC power supplyloop circuit power supplied via loop From 11-26VDC power supplyD-011-0152 Power Requirements InstallationTools and Supplies Required Mounting the EA800 Rear PlateEA800 Base Unit Power Connections Install the Wired SensorsInstall the Wireless Sensors SENSOR MODEL NO RESET BUTTONSENSOR MODEL NO RESET BUTTOND-011-0152 J6 Input 1 Input 2 Input 3 InputConnecting Wired HA-III+Humidity Sensors Connecting Wired 4-20mASensors Programming Connecting the EA800 Alarm OutputsConfiguring System Parameter Settings Accessing the MAIN MENU for Programming3.Enter the SYSTEM menu and then select the CONFIGURATION menu as shown below DISABLED is selected Setting the Current Date D-011-0152 Setting the TimeAdding a Wireless Temperature Sensor Adding Wireless SensorsD-011-0152 Adding Wireless SensorsD-011-0152 InstallationD-011-0152 Installation Adding a Wireless Humidity SensorD-011-0152 D-011-0152 D-011-0152 InstallationD-011-0152 Select N.O. Contact or N.C. Contact InstallationD-011-0152 D-011-0152 Verify Wireless Signal StrengthAdding a Wired Temperature Sensor Adding Wired SensorsAdding Wired Sensors Adding a Wired HA-III+Humidity SensorD-011-0152 Note A supervised WaterBug sensor must be used Adding a Wired WaterBug SensorSelect N.O. Contact or N.C. Contact Adding a Wired Contact Closure SensorD-011-0152 Adding a 4-20mASensor Configuring the Relays Monitoring Environmental Conditions OperationViewing Active Alarms Viewing Sensor SettingsViewing Pending Alarm Information Viewing the Alarm LogViewing the Event Log Viewing Limit SettingsViewing Firmware Information Viewing the Sensor LogOperation D-011-0152Viewing RF Information Viewing RF InformationLocking and Unlocking the EA800 MaintenancePausing Monitoring and Cancelling Pause Replacing a Sensor Adding a SensorSENSORS screen Editing Sensor ParametersDeleting a Sensor Reprogramming a RelayF3 F3 Changing the Time Format Changing the Date FormatChanging Sensor Data Collection Frequency Changing the Date or Time SettingChanging the Buzzer Setting Changing the Buzzer SettingMaintenance Changing the PasswordD-011-0152 Clearing the Sensor Log Clearing the Alarm LogClearing the Alarm Log Maintenance Updating the FirmwareD-011-0152 F3 LOAD/SAVE CONFIG screen Saving Configuration SettingsCONFIG screen Loading Configuration SettingsExporting the Stored Logs Exported Alarm DataExported Sensor Data Exported Event Data12/24/2007 07 06 03 PM Sensor deletedD-011-0152 Exporting the Stored LogsACTIVE ALARMS screen TroubleshootingViewing Signal Strength for a Wireless Sensor Verifying RF Signal StrengthBase Unit and Sensor Specifications SpecificationsAccessories Figure 17. Locked Screen Map Appendix A Screen MapsD-011-0152 Figure 18. Unlocked Screen Map - Top LevelFigure 19. Sensors Screen Map Appendix A Screen MapsD-011-0152 D-011-0152 Figure 20. Add New Sensor Screen MapFigure 21. Edit Sensor Screen Map Appendix A Screen MapsFigure 22. Relay Screen Map D-011-0152D-011-0152 Figure 23. Data Log Screen MapFigure 24. System Screen Map Appendix A Screen MapsD-011-0152 D-011-0152 Figure 25. Configuration Screen MapInstallation Appendix B Planning WorksheetAlarm Condition Appendix B Planning WorksheetD-011-0152 Appendix C Wiring DiagramD-011-0152 Appendix D System Configuration Record Unit of Measure Appendix D System Configuration Record Sensor 6 Settings wireless Appendix D System Configuration Record D-011-0152 Warranty and Service Information Winland Electronics Manufactured in the U.S.A by1950 Excel Drive, Mankato, MN, Outside MN Phone Phone Fax
Top Page Image Contents