Enviro EA800 owner manual Viewing Limit Settings, Viewing the Event Log

Page 56

Viewing Limit Settings

Viewing Limit Settings

Viewing Limit Settings

To view the current readings and the limits of a sensor that is not in an alarm state perform the following procedure:

To return to Active Alarm or Monitoring screen.

Viewing the Event Log

The EA800 Alarm System logs up to 100 events in its Event Log. At the minimum, the following events are logged:

■System power on: the date and time when the EA800 was powered on.

■Sensor added: indicates that a sensor was added.

■Sensor deleted: indicates that a sensor was deleted.

■WRM Msg error: indicates that an error message was generated.

■Firmware updated: indicates that the firmware was upgraded.

■Alarm log cleared: indicates when the alarm log was cleared.

■Data log cleared: indicates when the data log was cleared.

Note: Pressing either arrow key will eventually wrap to sequence number 1.

To review the event log, perform the following procedure:

Press arrow keys to scroll up or down through the logged events.

OR

To return to Active Alarm or Monitoring screen.

52	D-011-0152

Image 56

Contents D-011-0152 Limitations of the Alarm System or Device Table of Contents InstallationGeneral Information PreparationOperation General Information OverviewHow to Use This Manual D-011-0152 Block DiagramsGeneral Information Symbols on the Product or Manual Labeling D-011-0152 Monitoring ScreensGeneral Information Keys Base Unit Connections Access Control and Passwords selected System Configuration Parameterswill sound when an alarm occurs if DISABLE is Sensors Temperature SensorsTheory of Operation Humidity Sensors4-20mASensors Power Supply / Sensor Voltage Selection Contact Closure Sensors Water SensorsMulti-FunctionSensors Sensor Parameter Descriptions ResolutionMaximum Allowed High Scaled ValueRelay Operation Relay Operation D-011-0152Preparation D-011-0152 From 11-26VDC power supply To alarm-on-closedloop circuit power supplied via loop From 11-26VDC power supplyD-011-0152 Installation Power RequirementsTools and Supplies Required Mounting the EA800 Rear PlateInstall the Wireless Sensors Install the Wired SensorsEA800 Base Unit Power Connections RESET BUTTON SENSOR MODEL NORESET BUTTON SENSOR MODEL NOD-011-0152 J6 Input 1 Input 2 Input 3 InputConnecting Wired HA-III+Humidity Sensors Connecting Wired 4-20mASensors Connecting the EA800 Alarm Outputs ProgrammingAccessing the MAIN MENU for Programming Configuring System Parameter Settings3.Enter the SYSTEM menu and then select the CONFIGURATION menu as shown below DISABLED is selected Setting the Current Date Setting the Time D-011-0152Adding Wireless Sensors Adding a Wireless Temperature SensorAdding Wireless Sensors D-011-0152Installation D-011-0152D-011-0152 D-011-0152 Adding a Wireless Humidity SensorInstallation D-011-0152 Installation D-011-0152D-011-0152 D-011-0152 InstallationSelect N.O. Contact or N.C. Contact Verify Wireless Signal Strength D-011-0152Adding Wired Sensors Adding a Wired Temperature SensorD-011-0152 Adding a Wired HA-III+Humidity SensorAdding Wired Sensors Adding a Wired WaterBug Sensor Note A supervised WaterBug sensor must be usedD-011-0152 Adding a Wired Contact Closure SensorSelect N.O. Contact or N.C. Contact Adding a 4-20mASensor Configuring the Relays Operation Monitoring Environmental ConditionsViewing Sensor Settings Viewing Active AlarmsViewing the Alarm Log Viewing Pending Alarm InformationViewing Limit Settings Viewing the Event LogViewing the Sensor Log Viewing Firmware InformationOperation D-011-0152Viewing RF Information Viewing RF InformationMaintenance Locking and Unlocking the EA800Pausing Monitoring and Cancelling Pause Adding a Sensor Replacing a SensorEditing Sensor Parameters SENSORS screenF3 F3 Reprogramming a RelayDeleting a Sensor Changing the Date Format Changing the Time FormatChanging the Date or Time Setting Changing Sensor Data Collection FrequencyChanging the Buzzer Setting Changing the Buzzer SettingD-011-0152 Changing the PasswordMaintenance Clearing the Alarm Log Clearing the Alarm LogClearing the Sensor Log D-011-0152 Updating the FirmwareMaintenance Saving Configuration Settings F3 LOAD/SAVE CONFIG screenLoading Configuration Settings CONFIG screenExported Alarm Data Exporting the Stored LogsExported Event Data Exported Sensor Data12/24/2007 07 06 03 PM Sensor deletedExporting the Stored Logs D-011-0152Troubleshooting ACTIVE ALARMS screenVerifying RF Signal Strength Viewing Signal Strength for a Wireless SensorSpecifications Base Unit and Sensor SpecificationsAccessories Appendix A Screen Maps Figure 17. Locked Screen MapFigure 18. Unlocked Screen Map - Top Level D-011-0152D-011-0152 Appendix A Screen MapsFigure 19. Sensors Screen Map Figure 20. Add New Sensor Screen Map D-011-0152Appendix A Screen Maps Figure 21. Edit Sensor Screen MapFigure 22. Relay Screen Map D-011-0152Figure 23. Data Log Screen Map D-011-0152D-011-0152 Appendix A Screen MapsFigure 24. System Screen Map Figure 25. Configuration Screen Map D-011-0152Appendix B Planning Worksheet InstallationAlarm Condition Appendix B Planning WorksheetD-011-0152 C Wiring Diagram AppendixD-011-0152 Appendix D System Configuration Record Unit of Measure Appendix D System Configuration Record Sensor 6 Settings wireless Appendix D System Configuration Record D-011-0152 Warranty and Service Information Manufactured in the U.S.A by Winland Electronics1950 Excel Drive, Mankato, MN, Outside MN Phone Phone Fax