Enviro EA800 Viewing the Sensor Log, Viewing Firmware Information, Operation, D-011-0152

Page 57

Viewing the Sensor Log

Operation

Viewing the Sensor Log

The sensor log provides a history of the environmental conditions for all installed sensors at a glance. Up to

100 data sets are stored in the sensor log. To view the sensor log, perform the following procedure:

Press arrow keys to scroll up or down through the logged data.

OR

To return to Active Alarm or Monitoring screen.

Viewing Firmware Information

The About EA800 menu item displays the currently running firmware version. To view the firmware version, do the following:

Note: The firmware revision number shown indicates the firmware version currently installed.

To return to Active Alarm or Monitoring screen.

D-011-0152

53

Image 57

Contents D-011-0152 Limitations of the Alarm System or Device Installation Table of ContentsGeneral Information PreparationOperation Overview General InformationHow to Use This Manual Block Diagrams General InformationD-011-0152 Symbols on the Product or Manual Labeling Monitoring Screens General InformationD-011-0152 Keys Base Unit Connections Access Control and Passwords System Configuration Parameters will sound when an alarm occurs if DISABLE isselected Temperature Sensors SensorsHumidity Sensors 4-20mASensorsTheory of Operation Power Supply / Sensor Voltage Selection Water Sensors Multi-FunctionSensorsContact Closure Sensors Resolution Sensor Parameter DescriptionsMaximum Allowed High Scaled ValueRelay Operation D-011-0152 Relay OperationPreparation D-011-0152 To alarm-on-closed From 11-26VDC power supplyloop circuit power supplied via loop From 11-26VDC power supplyD-011-0152 Power Requirements InstallationTools and Supplies Required Mounting the EA800 Rear PlateInstall the Wired Sensors EA800 Base Unit Power ConnectionsInstall the Wireless Sensors SENSOR MODEL NO RESET BUTTONSENSOR MODEL NO RESET BUTTOND-011-0152 J6 Input 1 Input 2 Input 3 InputConnecting Wired HA-III+Humidity Sensors Connecting Wired 4-20mASensors Programming Connecting the EA800 Alarm OutputsConfiguring System Parameter Settings Accessing the MAIN MENU for Programming3.Enter the SYSTEM menu and then select the CONFIGURATION menu as shown below DISABLED is selected Setting the Current Date D-011-0152 Setting the TimeAdding a Wireless Temperature Sensor Adding Wireless SensorsD-011-0152 Adding Wireless SensorsD-011-0152 InstallationD-011-0152 Adding a Wireless Humidity Sensor InstallationD-011-0152 D-011-0152 D-011-0152 InstallationD-011-0152 Installation Select N.O. Contact or N.C. ContactD-011-0152 D-011-0152 Verify Wireless Signal StrengthAdding a Wired Temperature Sensor Adding Wired SensorsAdding a Wired HA-III+Humidity Sensor Adding Wired SensorsD-011-0152 Note A supervised WaterBug sensor must be used Adding a Wired WaterBug SensorAdding a Wired Contact Closure Sensor Select N.O. Contact or N.C. ContactD-011-0152 Adding a 4-20mASensor Configuring the Relays Monitoring Environmental Conditions OperationViewing Active Alarms Viewing Sensor SettingsViewing Pending Alarm Information Viewing the Alarm LogViewing the Event Log Viewing Limit SettingsViewing Firmware Information Viewing the Sensor LogOperation D-011-0152Viewing RF Information Viewing RF InformationLocking and Unlocking the EA800 MaintenancePausing Monitoring and Cancelling Pause Replacing a Sensor Adding a SensorSENSORS screen Editing Sensor ParametersReprogramming a Relay Deleting a SensorF3 F3 Changing the Time Format Changing the Date FormatChanging Sensor Data Collection Frequency Changing the Date or Time SettingChanging the Buzzer Setting Changing the Buzzer SettingChanging the Password MaintenanceD-011-0152 Clearing the Alarm Log Clearing the Sensor LogClearing the Alarm Log Updating the Firmware MaintenanceD-011-0152 F3 LOAD/SAVE CONFIG screen Saving Configuration SettingsCONFIG screen Loading Configuration SettingsExporting the Stored Logs Exported Alarm DataExported Sensor Data Exported Event Data12/24/2007 07 06 03 PM Sensor deletedD-011-0152 Exporting the Stored LogsACTIVE ALARMS screen TroubleshootingViewing Signal Strength for a Wireless Sensor Verifying RF Signal StrengthBase Unit and Sensor Specifications SpecificationsAccessories Figure 17. Locked Screen Map Appendix A Screen MapsD-011-0152 Figure 18. Unlocked Screen Map - Top LevelAppendix A Screen Maps Figure 19. Sensors Screen MapD-011-0152 D-011-0152 Figure 20. Add New Sensor Screen MapFigure 21. Edit Sensor Screen Map Appendix A Screen MapsFigure 22. Relay Screen Map D-011-0152D-011-0152 Figure 23. Data Log Screen MapAppendix A Screen Maps Figure 24. System Screen MapD-011-0152 D-011-0152 Figure 25. Configuration Screen MapInstallation Appendix B Planning WorksheetAlarm Condition Appendix B Planning WorksheetD-011-0152 Appendix C Wiring DiagramD-011-0152 Appendix D System Configuration Record Unit of Measure Appendix D System Configuration Record Sensor 6 Settings wireless Appendix D System Configuration Record D-011-0152 Warranty and Service Information Winland Electronics Manufactured in the U.S.A by1950 Excel Drive, Mankato, MN, Outside MN Phone Phone Fax