Enviro EA800 owner manual D-011-0152

Page 42

Manual background

Adding Wireless Sensors

Adding a Wireless Multi-Function Sensor Using a Wired WaterBug Sensor

Wireless multi-function sensors are physically connected to wired sensors located elsewhere and provide a transmitter to send the signals monitored by the wired sensor to the base unit. To add a wireless multi-function sensor, do the following:

1.Unlock the base unit if necessary to continue programming. See “Accessing the MAIN MENU for Programming” on page 28.

2.Select SENSORS from the MAIN MENU and follow the steps in the following diagram.

3.After you press the ENTER key, the NEW WIRELESS SENSOR screen is displayed. The EA800 searches for new wireless sensors, indicated by an arrow that moves from left to right across the screen. When an available wireless sensor has been detected, it is listed in the SELECT SENSOR screen as shown below.

4.Use the arrow keys to select the wireless multifunction sensor to be configured, then follow the prompts to configure all screens for that sensor.

To add a wireless WaterBug sensor to the system perform the following procedure.

1.Unlock the base unit if necessary to continue programming. See “Accessing the MAIN MENU for Programming” on page 28.

2.Select SENSORS from the MAIN MENU and follow the steps in the following diagram.

3.After you press the ENTER key, the NEW WIRELESS SENSOR screen is displayed. The EA800 searches for new wireless sensors, indicated by an arrow that moves from left to right across the screen. When an available wireless sensor has been detected, it is listed in the SELECT SENSOR screen as shown below.

4.Use the arrow keys to select the sensor to be configured, then follow the prompts to configure all screens for that sensor as shown in the following diagram.

38	D-011-0152

Image 42

Contents D-011-0152 Limitations of the Alarm System or Device General Information Table of ContentsInstallation PreparationOperation General Information OverviewHow to Use This Manual Block Diagrams General InformationD-011-0152 Symbols on the Product or Manual Labeling Monitoring Screens General InformationD-011-0152 Keys Base Unit Connections Access Control and Passwords System Configuration Parameters will sound when an alarm occurs if DISABLE isselected Sensors Temperature SensorsHumidity Sensors 4-20mASensorsTheory of Operation Power Supply / Sensor Voltage Selection Water Sensors Multi-FunctionSensorsContact Closure Sensors Maximum Allowed Sensor Parameter DescriptionsResolution High Scaled ValueRelay Operation Relay Operation D-011-0152Preparation D-011-0152 loop circuit power supplied via loop From 11-26VDC power supplyTo alarm-on-closed From 11-26VDC power supplyD-011-0152 Tools and Supplies Required InstallationPower Requirements Mounting the EA800 Rear PlateInstall the Wired Sensors EA800 Base Unit Power ConnectionsInstall the Wireless Sensors RESET BUTTON SENSOR MODEL NOD-011-0152 RESET BUTTONSENSOR MODEL NO J6 Input 1 Input 2 Input 3 InputConnecting Wired HA-III+Humidity Sensors Connecting Wired 4-20mASensors Connecting the EA800 Alarm Outputs ProgrammingAccessing the MAIN MENU for Programming Configuring System Parameter Settings3.Enter the SYSTEM menu and then select the CONFIGURATION menu as shown below DISABLED is selected Setting the Current Date Setting the Time D-011-0152Adding Wireless Sensors Adding a Wireless Temperature SensorAdding Wireless Sensors D-011-0152Installation D-011-0152D-011-0152 Adding a Wireless Humidity Sensor InstallationD-011-0152 D-011-0152 Installation D-011-0152D-011-0152 Installation Select N.O. Contact or N.C. ContactD-011-0152 Verify Wireless Signal Strength D-011-0152Adding Wired Sensors Adding a Wired Temperature SensorAdding a Wired HA-III+Humidity Sensor Adding Wired SensorsD-011-0152 Adding a Wired WaterBug Sensor Note A supervised WaterBug sensor must be usedAdding a Wired Contact Closure Sensor Select N.O. Contact or N.C. ContactD-011-0152 Adding a 4-20mASensor Configuring the Relays Operation Monitoring Environmental ConditionsViewing Sensor Settings Viewing Active AlarmsViewing the Alarm Log Viewing Pending Alarm InformationViewing Limit Settings Viewing the Event LogOperation Viewing the Sensor LogViewing Firmware Information D-011-0152Viewing RF Information Viewing RF InformationMaintenance Locking and Unlocking the EA800Pausing Monitoring and Cancelling Pause Adding a Sensor Replacing a SensorEditing Sensor Parameters SENSORS screenReprogramming a Relay Deleting a SensorF3 F3 Changing the Date Format Changing the Time FormatChanging the Date or Time Setting Changing Sensor Data Collection FrequencyChanging the Buzzer Setting Changing the Buzzer SettingChanging the Password MaintenanceD-011-0152 Clearing the Alarm Log Clearing the Sensor LogClearing the Alarm Log Updating the Firmware MaintenanceD-011-0152 Saving Configuration Settings F3 LOAD/SAVE CONFIG screenLoading Configuration Settings CONFIG screenExported Alarm Data Exporting the Stored Logs12/24/2007 07 06 03 PM Exported Event DataExported Sensor Data Sensor deletedExporting the Stored Logs D-011-0152Troubleshooting ACTIVE ALARMS screenVerifying RF Signal Strength Viewing Signal Strength for a Wireless SensorSpecifications Base Unit and Sensor SpecificationsAccessories Appendix A Screen Maps Figure 17. Locked Screen MapFigure 18. Unlocked Screen Map - Top Level D-011-0152Appendix A Screen Maps Figure 19. Sensors Screen MapD-011-0152 Figure 20. Add New Sensor Screen Map D-011-0152Figure 22. Relay Screen Map Appendix A Screen MapsFigure 21. Edit Sensor Screen Map D-011-0152Figure 23. Data Log Screen Map D-011-0152Appendix A Screen Maps Figure 24. System Screen MapD-011-0152 Figure 25. Configuration Screen Map D-011-0152Alarm Condition Appendix B Planning WorksheetInstallation Appendix B Planning WorksheetD-011-0152 C Wiring Diagram AppendixD-011-0152 Appendix D System Configuration Record Unit of Measure Appendix D System Configuration Record Sensor 6 Settings wireless Appendix D System Configuration Record D-011-0152 Warranty and Service Information 1950 Excel Drive, Mankato, MN, Outside MN Phone Manufactured in the U.S.A byWinland Electronics Phone Fax