Enviro EA800 owner manual Pausing Monitoring and Cancelling Pause

Page 60

Pausing Monitoring and Cancelling Pause

Pausing Monitoring and Cancelling Pause

Pausing Monitoring and Cancelling Pause

To prevent false alarms when performing maintenance, pause sensor monitoring. Pausing stops monitoring and ignores active alarms for a 30-minute period. When the pause function times out, monitoring automatically starts. To pause the EA800 perform the following procedure:

Unlock as shown in “Locking and Unlocking the EA800” on page 55

F3

OR

To cancel pause and resume monitoring

F2

When the system is paused the SYSTEM PAUSED screen is displayed until pause times out (30 minutes) or you cancel it. You can access all functions in the main menu while the system is paused. To resume monitoring instead of allowing the pause function to time out perform the following procedure:

Unlock as shown in “Locking and Unlocking the EA800” on page 55

F2

56	D-011-0152

Image 60

Contents D-011-0152 Limitations of the Alarm System or Device Table of Contents InstallationGeneral Information PreparationOperation General Information OverviewHow to Use This Manual Block Diagrams General InformationD-011-0152 Symbols on the Product or Manual Labeling Monitoring Screens General InformationD-011-0152 Keys Base Unit Connections Access Control and Passwords System Configuration Parameters will sound when an alarm occurs if DISABLE isselected Sensors Temperature SensorsHumidity Sensors 4-20mASensorsTheory of Operation Power Supply / Sensor Voltage Selection Water Sensors Multi-FunctionSensorsContact Closure Sensors Sensor Parameter Descriptions ResolutionMaximum Allowed High Scaled ValueRelay Operation Relay Operation D-011-0152Preparation D-011-0152 From 11-26VDC power supply To alarm-on-closedloop circuit power supplied via loop From 11-26VDC power supplyD-011-0152 Installation Power RequirementsTools and Supplies Required Mounting the EA800 Rear PlateInstall the Wired Sensors EA800 Base Unit Power ConnectionsInstall the Wireless Sensors RESET BUTTON SENSOR MODEL NORESET BUTTON SENSOR MODEL NOD-011-0152 J6 Input 1 Input 2 Input 3 InputConnecting Wired HA-III+Humidity Sensors Connecting Wired 4-20mASensors Connecting the EA800 Alarm Outputs ProgrammingAccessing the MAIN MENU for Programming Configuring System Parameter Settings3.Enter the SYSTEM menu and then select the CONFIGURATION menu as shown below DISABLED is selected Setting the Current Date Setting the Time D-011-0152Adding Wireless Sensors Adding a Wireless Temperature SensorAdding Wireless Sensors D-011-0152Installation D-011-0152D-011-0152 Adding a Wireless Humidity Sensor InstallationD-011-0152 D-011-0152 Installation D-011-0152D-011-0152 Installation Select N.O. Contact or N.C. ContactD-011-0152 Verify Wireless Signal Strength D-011-0152Adding Wired Sensors Adding a Wired Temperature SensorAdding a Wired HA-III+Humidity Sensor Adding Wired SensorsD-011-0152 Adding a Wired WaterBug Sensor Note A supervised WaterBug sensor must be usedAdding a Wired Contact Closure Sensor Select N.O. Contact or N.C. ContactD-011-0152 Adding a 4-20mASensor Configuring the Relays Operation Monitoring Environmental ConditionsViewing Sensor Settings Viewing Active AlarmsViewing the Alarm Log Viewing Pending Alarm InformationViewing Limit Settings Viewing the Event LogViewing the Sensor Log Viewing Firmware InformationOperation D-011-0152Viewing RF Information Viewing RF InformationMaintenance Locking and Unlocking the EA800Pausing Monitoring and Cancelling Pause Adding a Sensor Replacing a SensorEditing Sensor Parameters SENSORS screenReprogramming a Relay Deleting a SensorF3 F3 Changing the Date Format Changing the Time FormatChanging the Date or Time Setting Changing Sensor Data Collection FrequencyChanging the Buzzer Setting Changing the Buzzer SettingChanging the Password MaintenanceD-011-0152 Clearing the Alarm Log Clearing the Sensor LogClearing the Alarm Log Updating the Firmware MaintenanceD-011-0152 Saving Configuration Settings F3 LOAD/SAVE CONFIG screenLoading Configuration Settings CONFIG screenExported Alarm Data Exporting the Stored LogsExported Event Data Exported Sensor Data12/24/2007 07 06 03 PM Sensor deletedExporting the Stored Logs D-011-0152Troubleshooting ACTIVE ALARMS screenVerifying RF Signal Strength Viewing Signal Strength for a Wireless SensorSpecifications Base Unit and Sensor SpecificationsAccessories Appendix A Screen Maps Figure 17. Locked Screen MapFigure 18. Unlocked Screen Map - Top Level D-011-0152Appendix A Screen Maps Figure 19. Sensors Screen MapD-011-0152 Figure 20. Add New Sensor Screen Map D-011-0152Appendix A Screen Maps Figure 21. Edit Sensor Screen MapFigure 22. Relay Screen Map D-011-0152Figure 23. Data Log Screen Map D-011-0152Appendix A Screen Maps Figure 24. System Screen MapD-011-0152 Figure 25. Configuration Screen Map D-011-0152Appendix B Planning Worksheet InstallationAlarm Condition Appendix B Planning WorksheetD-011-0152 C Wiring Diagram AppendixD-011-0152 Appendix D System Configuration Record Unit of Measure Appendix D System Configuration Record Sensor 6 Settings wireless Appendix D System Configuration Record D-011-0152 Warranty and Service Information Manufactured in the U.S.A by Winland Electronics1950 Excel Drive, Mankato, MN, Outside MN Phone Phone Fax