Enviro EA800 owner manual Changing the Buzzer Setting

Page 66
Changing the Buzzer Setting

Changing the Buzzer Setting

Changing the Buzzer Setting

 

 

Changing the buzzer setting to DISABLED turns off the audible alarm tone from

!

WARNING

the base unit. Do not disable the buzzer unless you are sure you do not want the

 

 

 

 

base unit to emit an audible tone when an alarm occurs. The active condition of

 

 

the buzzer mirrors what is assigned to the auxiliary relay.

Note: Update the system’s Configuration Worksheets to document any changes.

Note: The default buzzer configuration is ENABLED and the active condition of the on-board buzzer mirrors what is assigned to the Auxiliary Relay.

To change the buzzer setting perform the following procedure:

Unlock the EA800 as shown in “Locking and Unlocking the EA800” on page 55

Manual background F3 Manual background

62

D-011-0152

Image 66
Contents D-011-0152 Limitations of the Alarm System or Device General Information Table of ContentsInstallation PreparationOperation General Information OverviewHow to Use This Manual Block Diagrams General InformationD-011-0152 Symbols on the Product or Manual Labeling Monitoring Screens General InformationD-011-0152 Keys Base Unit Connections Access Control and Passwords System Configuration Parameters will sound when an alarm occurs if DISABLE isselected Sensors Temperature SensorsHumidity Sensors 4-20mASensorsTheory of Operation Power Supply / Sensor Voltage Selection Water Sensors Multi-FunctionSensorsContact Closure Sensors Maximum Allowed Sensor Parameter DescriptionsResolution High Scaled ValueRelay Operation Relay Operation D-011-0152Preparation D-011-0152 loop circuit power supplied via loop From 11-26VDC power supplyTo alarm-on-closed From 11-26VDC power supplyD-011-0152 Tools and Supplies Required InstallationPower Requirements Mounting the EA800 Rear PlateInstall the Wired Sensors EA800 Base Unit Power ConnectionsInstall the Wireless Sensors RESET BUTTON SENSOR MODEL NOD-011-0152 RESET BUTTONSENSOR MODEL NO J6 Input 1 Input 2 Input 3 InputConnecting Wired HA-III+Humidity Sensors Connecting Wired 4-20mASensors Connecting the EA800 Alarm Outputs ProgrammingAccessing the MAIN MENU for Programming Configuring System Parameter Settings3.Enter the SYSTEM menu and then select the CONFIGURATION menu as shown below DISABLED is selected Setting the Current Date Setting the Time D-011-0152Adding Wireless Sensors Adding a Wireless Temperature SensorAdding Wireless Sensors D-011-0152Installation D-011-0152D-011-0152 Adding a Wireless Humidity Sensor InstallationD-011-0152 D-011-0152 Installation D-011-0152D-011-0152 Installation Select N.O. Contact or N.C. ContactD-011-0152 Verify Wireless Signal Strength D-011-0152Adding Wired Sensors Adding a Wired Temperature SensorAdding a Wired HA-III+Humidity Sensor Adding Wired SensorsD-011-0152 Adding a Wired WaterBug Sensor Note A supervised WaterBug sensor must be usedAdding a Wired Contact Closure Sensor Select N.O. Contact or N.C. ContactD-011-0152 Adding a 4-20mASensor Configuring the Relays Operation Monitoring Environmental ConditionsViewing Sensor Settings Viewing Active AlarmsViewing the Alarm Log Viewing Pending Alarm InformationViewing Limit Settings Viewing the Event LogOperation Viewing the Sensor LogViewing Firmware Information D-011-0152Viewing RF Information Viewing RF InformationMaintenance Locking and Unlocking the EA800Pausing Monitoring and Cancelling Pause Adding a Sensor Replacing a SensorEditing Sensor Parameters SENSORS screenReprogramming a Relay Deleting a SensorF3 F3 Changing the Date Format Changing the Time FormatChanging the Date or Time Setting Changing Sensor Data Collection FrequencyChanging the Buzzer Setting Changing the Buzzer SettingChanging the Password MaintenanceD-011-0152 Clearing the Alarm Log Clearing the Sensor LogClearing the Alarm Log Updating the Firmware MaintenanceD-011-0152 Saving Configuration Settings F3 LOAD/SAVE CONFIG screenLoading Configuration Settings CONFIG screenExported Alarm Data Exporting the Stored Logs12/24/2007 07 06 03 PM Exported Event DataExported Sensor Data Sensor deletedExporting the Stored Logs D-011-0152Troubleshooting ACTIVE ALARMS screenVerifying RF Signal Strength Viewing Signal Strength for a Wireless SensorSpecifications Base Unit and Sensor SpecificationsAccessories Appendix A Screen Maps Figure 17. Locked Screen MapFigure 18. Unlocked Screen Map - Top Level D-011-0152Appendix A Screen Maps Figure 19. Sensors Screen MapD-011-0152 Figure 20. Add New Sensor Screen Map D-011-0152Figure 22. Relay Screen Map Appendix A Screen MapsFigure 21. Edit Sensor Screen Map D-011-0152Figure 23. Data Log Screen Map D-011-0152Appendix A Screen Maps Figure 24. System Screen MapD-011-0152 Figure 25. Configuration Screen Map D-011-0152Alarm Condition Appendix B Planning WorksheetInstallation Appendix B Planning WorksheetD-011-0152 C Wiring Diagram AppendixD-011-0152 Appendix D System Configuration Record Unit of Measure Appendix D System Configuration Record Sensor 6 Settings wireless Appendix D System Configuration Record D-011-0152 Warranty and Service Information 1950 Excel Drive, Mankato, MN, Outside MN Phone Manufactured in the U.S.A byWinland Electronics Phone Fax