Quadra-Fire CB1200I-B owner manual Rear Vent Installation Preparation, For Top Vent Installation

Page 18

CB1200-I Pellet Insert

R

Rear Vent Installation Preparation:

1.

Remove the ENTIRE exhaust blower housing by remov-

 

ing the 4 nuts using a 7/16" socket wrench. Set the nuts

 

aside for later use.

2.

Remove the 4 screws and remove the vertical exhaust

 

transition pipe exhaust blower housing.

3.

Remove any silicone sealant remaining on the blower

 

housing.

4.

Attach the rear vent adapter to the exhaust blower hous-

 

ing with 4 screws. Figure 18.2.

5.

Apply a bead of high temperature silicone adhesive

 

around the juncture of the blower housing and rear vent

 

adapter, smoothing it around the joint to ensure that a

 

good seal is made.

6.

Re-install the exhaust blower housing (now with rear vent

 

adapter attached) with the 4 nuts previously removed in

4.Assemble the right corner and right panel pieces using 4 screws prior to attaching to insert. Figure 18.4.

5.After assembly, attach the right shroud panel/corner piece assembly to the insert with 3 screws across the bottom and 1 on the side. Figure 18.4.

 

Knock-Out

 

Plate

Outside Air

 

Cover Plate

 

Left Side

Figure 18.3

 

Step 1.

7.

Use 2 screws to attach left corner filler piece of rear

 

shroud to the insert hopper. Figures 17.1 & 17.2 on

 

page 17.

8.

Install the left shroud corner with 2 screws into the hopper

 

body and 1 down into filler piece. Figure 18.1.

9.

Install cover plate over top vent opening using 4

 

screws.

Attach right

corner piece to side panel first.

Right Side

Right Corner Piece

Rear Panel

Left Corner

Piece

Figure 18.1

Figure 18.2

 

Installing Rear Shroud

Figure 18.4

Attaching Shroud to Hopper Body:

6.Beginning at the right shroud panel drill into hopper body through the 3 pre-drilled openings and the 2 pre-drilled openings on the rear shroud panel. Figure 18.5. Continue around to left shroud corner panel at the 2 pre-drilled openings. Figure 18.6. Secure with screws to insert.

7.For Top Vent Installation:

Install 3 inch or 4 inch (76 or 102mm) top vent adapter. See circled area in Figure 17.3 on page 17. NOTE: This adapter may be attached to outside venting prior to latching it on to the top vent pipe.

Drill Holes

Drill Holes

Top Vent Applications: Leave knock-out plate in place.

 

 

 

 

 

Figure 18.3

 

 

 

 

 

 

 

 

Rear Panel

Rear Vent Applications: Clip corners of knock-out plate,

Figure 18.5

remove and discard, prior to assembling rear shroud kit.

 

 

 

 

 

1. Install rear panel using 4 screws along bottom and 2 screws

 

 

 

 

 

into the left shroud corner piece at the top. Figure 18.3.

 

 

 

 

 

 

 

 

Drill Holes

 

 

 

 

 

 

2.If your installation does not include an outside air kit, attach cover plate with 4 screws.

3.Attach left shroud panel using seven screws, 3 on top and

bottom and 1 along the side. Figure 18.3.

 

Figure 18.6

 

 

 

 

 

 

 

 

Page 18

7014-083C

October 26, 2006

Page 17 Page 19
Image 18
Page 17 Page 19
Contents CB1200I-B Welcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Listing and Code Approvals Getting Started Design, Installation & Location ConsiderationsFire Safety Appliance LocationCB1200-I Pellet Insert Tools And Supplies Needed Measuring StandardsInspect Appliance & Components and Pre-Use Check List Dimensions and Clearances Appliance DimensionsShown with Rear Vent and Optional Outside Air Inch 0mm Clearance to Exposed Section and Face TrimFace Trim CB1200-I Pellet Insert Masonry Minimum Opening Floor ProtectionCalculating Alternate Floor Protection Material Starter hole Mark area of floor to cut Install vent at clearances specified by Vent InformationVent manufacturer Pipe Selection Chart CB1200-I Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems CB1200-I Pellet Insert Full Reline With Outside Air Mobile Home Installation You must use a Quadra-Fire Outside Air Kit for instalLation in a mobile home Rear Shroud Installation Appliance Set-UpRear Vent Installation Preparation Installing Rear Shroud Attaching Shroud to Hopper BodyFor Top Vent Installation To adjust hopper Adjustable Hopper OptionsOptional Grille Installation CB1200-I Pellet Insert Outside Air Kit InstructionsCB1200-I Pellet Insert Adjustable Hearth Support Size 9d x 45w, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCharred Areas in the Back Operating Instructions Fuel Size And Material General Operating InformationFeed Rate Adjustment Instructions Fuel Adjustment Control RodFire Characteristics CB1200-I Pellet Insert Before Your First FireFrequently Asked Questions Do not Leave Firepot Floor OpenTroubleshooting SymptomPossible Cause Corrective Action Page Page CB10Maintaining & Servicing Your Appliance Pellet InsertCleaning Exhaust Path Cleaning Heat Exchanger ChambersCleaning Beneath Heat Exchanger Cleaning the Glass Frequency As neededHigh Ash Fuel Content Maintenance Igniter Replacement Replacing Side Glass Top frame when removing and replacing center GlassReplacing Center Glass Ered Phillips head screw driver to remove ScrewsReference Materials Component FunctionSnap Disc #1 Convection Blower 125F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Fuel Delivery Interrupt 200FBeginning Manufacture Date April 8 CB1200-I Pellet Insert Component LocationsExploded Views Glass Size Center 13-7/8 wide x 11 high Glass Size SidesBeg. Manufacture Date July CB1200-I Pellet Insert Service Parts and Accessories Nbr DescriptionItem # Part Descsription, Alphabetical Order 7014-083C October 26 Item No Accessories ApplianceCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceLifetime Warranty CB1200-I Pellet Insert Warranty PolicyCB1200-I Pellet Insert Telephone
Top Page Image Contents