Quadra-Fire CB1200I-B Snap Disc #1 Convection Blower 125F, Snap Disc #3 Burn Back Protector 250F

Page 36

CB1200-I Pellet Insert

R

16.Snap Disc #1 (Convection Blower) 125°F

Snap disc #1 is located on the right side of the firebox. There are 2 purple wires connected to it. This snap disc turns the convection blower on and off as needed. Power is always present at snap disc #1.

17.Snap Disc #2 (Fuel Delivery Interrupt) 200°F

Snap disc #2 is located on the back side of the feed drop tube. There is 1 orange wire and 1 black wire connected to it. This snap disc will turn off the feed system, which will turn off the appliance if an overfire condition should occur or if the convection blower should fail to operate. If this occurs the snap disc with automatically reset itself.

18.Snap Disc #3 (Burn Back Protector) 250°F

Snap disc #3 is mounted on the right side of the auger tube just below feed motor and has a reset button. To access it remove the right side panel. If the fire tries to burn back into the feed system or push exhaust up the feed tube, this snap disc will shut the entire system off. This disc must be manually reset.

19.Vacuum Switch

The vacuum switch is located at the rear of the appliance. This switch turns the feed system on when vacuum is present in the firebox. The vacuum switch is a safety device to shut off the feed motor if the exhaust or the heat exchanger system is dirty or plugged or if the firebox door is open.

20.Wiring Harness See Figure 36.1 below

T-STAT CONN (YEL)

T-STAT CONN

SNAP DISC #2 (YEL)

SNAP DISC #2 (YEL)

SNAP DISC # (GRAY)

SNAP DISC #1 (PUR)

SNAP DISC #1 (PUR)

POWER IN (BLK)

BLK

M BLK

CONV. BLOWER

 

 

 

 

 

WHITE

 

RED

AUGER MOTOR (RED/WHT)

 

 

 

 

 

M

AUGER MOTOR (BLK)

 

 

BLK

 

WHITE

 

 

VAC.

 

M BLK COMB BLOWER (BLU) SWITCH

 

 

BLK

NEUTRAL IN (WHT)

 

 

 

NEUTRAL AUGER

(WHT)

 

 

 

NEUTRAL CONV

(WHT)

 

 

 

NEUTRAL COMB

(WHT)

NEUTRAL IGN (HT)

IGNITER (HT)

Figure 36.1

AUG. CAP.

 

4

5

6

ACCY

 

 

 

 

 

1

2

3

JUMPER

 

 

 

 

 

 

BURN R ATE

 

 

 

 

BLUE

 

 

 

 

PURPLE

 

P.B.

LIGHT

ORANGE

 

 

 

 

GRAY

ORANGE

YELLOW

 

 

BLACK

 

 

 

 

HI-TEMP HI-TEMP BLUE GRAY PURPLE RED YELLOW YELLOW YELLOW BLUE WHITE ORANGE BLACK PURPLE RED

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

FUSE

.

RED

T.C

 

 

YELLOW

T/C

Page 36

7014-083C

October 26, 2006

Page 35 Page 37
Image 36
Page 35 Page 37
Contents CB1200I-B Welcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Listing and Code Approvals Design, Installation & Location Considerations Fire SafetyGetting Started Appliance LocationCB1200-I Pellet Insert Tools And Supplies Needed Measuring StandardsInspect Appliance & Components and Pre-Use Check List Dimensions and Clearances Appliance DimensionsShown with Rear Vent and Optional Outside Air Inch 0mm Clearance to Exposed Section and Face TrimFace Trim CB1200-I Pellet Insert Masonry Minimum Opening Floor ProtectionCalculating Alternate Floor Protection Material Starter hole Mark area of floor to cut Install vent at clearances specified by Vent InformationVent manufacturer Pipe Selection Chart CB1200-I Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems CB1200-I Pellet Insert Full Reline With Outside Air Mobile Home Installation You must use a Quadra-Fire Outside Air Kit for instalLation in a mobile home Rear Shroud Installation Appliance Set-UpRear Vent Installation Preparation Installing Rear Shroud Attaching Shroud to Hopper BodyFor Top Vent Installation Adjustable Hopper Options Optional Grille InstallationTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsCB1200-I Pellet Insert Adjustable Hearth Support Size 9d x 45w, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCharred Areas in the Back Operating Instructions Fuel Size And Material General Operating InformationFuel Adjustment Control Rod Fire CharacteristicsFeed Rate Adjustment Instructions CB1200-I Pellet Insert Before Your First FireFrequently Asked Questions Do not Leave Firepot Floor OpenTroubleshooting SymptomPossible Cause Corrective Action Page Page CB10Maintaining & Servicing Your Appliance Pellet InsertCleaning Heat Exchanger Chambers Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the Glass Frequency As neededHigh Ash Fuel Content Maintenance Igniter Replacement Top frame when removing and replacing center Glass Replacing Center GlassReplacing Side Glass Ered Phillips head screw driver to remove ScrewsReference Materials Component FunctionVacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 125F Snap Disc #2 Fuel Delivery Interrupt 200FCB1200-I Pellet Insert Component Locations Exploded ViewsBeginning Manufacture Date April 8 Glass Size Center 13-7/8 wide x 11 high Glass Size SidesBeg. Manufacture Date July CB1200-I Pellet Insert Service Parts and Accessories Nbr DescriptionItem # Part Descsription, Alphabetical Order 7014-083C October 26 Item No Accessories ApplianceCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceLifetime Warranty CB1200-I Pellet Insert Warranty PolicyCB1200-I Pellet Insert Telephone
Top Page Image Contents