Quadra-Fire CB1200I-B owner manual Replacing Center Glass, Replacing Side Glass

Page 34

CB1200-I Pellet Insert

 

R

E. Glass Replacement

 

Door Latch

 

 

 

 

WARNING

Top & Bottom Frame

 

 

 

 

 

• Glass is 5mm thick high temperature heat-

 

 

 

resistant ceramic glass.

 

 

 

• DO NOT REPLACE with any other material.

Center Posts

 

 

• Alternate material may shatter and cause

 

 

 

injury

 

Side

 

 

Glass

•

Remove door from appliance and place face down on

Frame

 

 

 

a protected surface to avoid scratching the door.

 

 

•

Remove all door rope.

 

 

Replacing Center Glass

 

 

NOTE: DO NOT LET Air Wash Spacers fall down from

Figure 34.1

 

 

top frame when removing and replacing center

 

 

glass.

 

 

1. Using a nut driver remove the (5) bottom nuts and

Remove Door Latch First

remove the bottom glass frame. Figure 34.2.

and then Side Frame

 

2.Slightly bend up and out of the way the 2 center posts and slide the glass out the bottom.

3.

Slide new glass in, reposition the 2 center posts and

 

Door Frame

 

re-install bottom glass frame.

 

 

 

shown with no

4.

Re-rope the door.

 

 

Glass or Glass

Replacing Side Glass

 

Frames

 

 

NOTE: When removing the side glass with the door

 

 

 

latch, you must remove the door latch first

 

 

 

before removing the side frame. Use a pow-

 

Remove 5 nuts from Bottom Frame

 

ered Phillips head screw driver to remove the

 

 

 

 

 

4 screws.

 

 

1.

Remove side glass frame.

 

 

 

Figure 34.2

2.

Loosen the top and bottom frame and slightly bend up

 

 

 

 

and out of the way.

F. Baffle Removal

3.

Slide glass out the side and slide new glass in.

1. Allow appliance to cool completely.

4.

Re-install the side glass frame and tighten the top and

2. Open glass door.

 

bottom frames.

 

3. Grab the bottom of the baffles and pull up to dislodge

5.

Re-install the door latch, if applicable, and re-rope the

 

from hook attachment.

 

door.

 

 

 

 

4. Use a standard screw driver to unlatch the covers beneath the baffles of each side.

5. Re-install in reverse order.

Page 34

7014-083C

October 26, 2006

Page 33 Page 35
Image 34
Page 33 Page 35
Contents CB1200I-B Welcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Listing and Code Approvals Getting Started Design, Installation & Location ConsiderationsFire Safety Appliance LocationMeasuring Standards CB1200-I Pellet Insert Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List Dimensions and Clearances Appliance DimensionsShown with Rear Vent and Optional Outside Air Inch 0mm Clearance to Exposed Section and Face TrimFace Trim Floor Protection CB1200-I Pellet Insert Masonry Minimum OpeningCalculating Alternate Floor Protection Material Starter hole Mark area of floor to cut Vent Information Install vent at clearances specified byVent manufacturer CB1200-I Pellet Insert Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems CB1200-I Pellet Insert Full Reline With Outside Air You must use a Quadra-Fire Outside Air Kit for instal Mobile Home InstallationLation in a mobile home Rear Shroud Installation Appliance Set-UpInstalling Rear Shroud Attaching Shroud to Hopper Body Rear Vent Installation PreparationFor Top Vent Installation To adjust hopper Adjustable Hopper OptionsOptional Grille Installation CB1200-I Pellet Insert Outside Air Kit InstructionsCB1200-I Pellet Insert Adjustable Hearth Support Size 9d x 45w, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCharred Areas in the Back Operating Instructions Fuel Size And Material General Operating InformationFeed Rate Adjustment Instructions Fuel Adjustment Control RodFire Characteristics CB1200-I Pellet Insert Before Your First FireFrequently Asked Questions Do not Leave Firepot Floor OpenSymptom TroubleshootingPossible Cause Corrective Action Page Page CB10Maintaining & Servicing Your Appliance Pellet InsertCleaning Exhaust Path Cleaning Heat Exchanger ChambersCleaning Beneath Heat Exchanger Cleaning the Glass Frequency As neededHigh Ash Fuel Content Maintenance Igniter Replacement Replacing Side Glass Top frame when removing and replacing center GlassReplacing Center Glass Ered Phillips head screw driver to remove ScrewsReference Materials Component FunctionSnap Disc #1 Convection Blower 125F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Fuel Delivery Interrupt 200FBeginning Manufacture Date April 8 CB1200-I Pellet Insert Component LocationsExploded Views Glass Size Center 13-7/8 wide x 11 high Glass Size SidesBeg. Manufacture Date July Nbr Description CB1200-I Pellet Insert Service Parts and AccessoriesItem # Part Descsription, Alphabetical Order 7014-083C October 26 Item No Accessories ApplianceCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceLifetime Warranty CB1200-I Pellet Insert Warranty PolicyCB1200-I Pellet Insert Telephone
Top Page Image Contents