Quadra-Fire CB1200I-B owner manual Shown with Rear Vent and Optional Outside Air

Page 8

CB1200-I Pellet Insert

B. Clearance To Combustibles, UL and ULC

AS A BUILT-IN

Rear Shroud Kit, Part 811-0680 is Required for Built-In Installation (see pages 17-18 for installation instructions)

A	D	C
B		B
C
		E

0 inch (0mm) Clearance to Exposed Section and Face Trim

R

Figure 8.1
Figure 8.1				Inches	Millimeters
				Inches	Millimeters
	A	Top of Shroud	Top Vent	3.0	76
			Rear Vent	0	0
	B	Sides of Inside Shroud	Top or Rear Vent	0	0
	C	Back of Inside Shroud	Top Vent	2.5	64
			Rear Vent	0	0
	D	Vent Pipe to Combustible	Top or Rear Vent	3.0	76
	E	From Outside Edge of		0	0
		Panel Set to Combustibles		0	0
		Panel Set to Combustibles

INSTALLED AS A BUILT-IN UNIT

Shown with Rear Vent and Optional Outside Air

Combustible

Mantel

Shown with Hopper Extended

12 in

6 in

Rear Shroud

Optional Outside

Air

Figure 8.2

WARNING

Fire Risk.

Comply with all minimum clear- ances to combustibles as speci- fied.

Failure to comply may cause house fire.

NOTE:

•Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY.

•Illustrations/diagrams are not drawn to scale.

•Actual installation may vary due to individual design preference.

Page

7014-083C

October 26, 2006

Image 8

Contents CB1200I-B Welcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Listing and Code Approvals Design, Installation & Location Considerations Fire SafetyGetting Started Appliance LocationInspect Appliance & Components and Pre-Use Check List CB1200-I Pellet Insert Tools And Supplies NeededMeasuring Standards Dimensions and Clearances Appliance DimensionsShown with Rear Vent and Optional Outside Air Inch 0mm Clearance to Exposed Section and Face TrimFace Trim Calculating Alternate Floor Protection Material CB1200-I Pellet Insert Masonry Minimum OpeningFloor Protection Starter hole Mark area of floor to cut Vent manufacturer Install vent at clearances specified byVent Information Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCB1200-I Pellet Insert Equivalent Feet of Pipe Venting Systems CB1200-I Pellet Insert Full Reline With Outside Air Lation in a mobile home Mobile Home InstallationYou must use a Quadra-Fire Outside Air Kit for instal Rear Shroud Installation Appliance Set-UpFor Top Vent Installation Rear Vent Installation PreparationInstalling Rear Shroud Attaching Shroud to Hopper Body Adjustable Hopper Options Optional Grille InstallationTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsCB1200-I Pellet Insert Adjustable Hearth Support Size 9d x 45w, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCharred Areas in the Back Operating Instructions Fuel Size And Material General Operating InformationFuel Adjustment Control Rod Fire CharacteristicsFeed Rate Adjustment Instructions CB1200-I Pellet Insert Before Your First FireFrequently Asked Questions Do not Leave Firepot Floor OpenPossible Cause Corrective Action TroubleshootingSymptom Page Page CB10Maintaining & Servicing Your Appliance Pellet InsertCleaning Heat Exchanger Chambers Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the Glass Frequency As neededHigh Ash Fuel Content Maintenance Igniter Replacement Top frame when removing and replacing center Glass Replacing Center GlassReplacing Side Glass Ered Phillips head screw driver to remove ScrewsReference Materials Component FunctionVacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 125F Snap Disc #2 Fuel Delivery Interrupt 200FCB1200-I Pellet Insert Component Locations Exploded ViewsBeginning Manufacture Date April 8 Glass Size Center 13-7/8 wide x 11 high Glass Size SidesBeg. Manufacture Date July Item # Part Descsription, Alphabetical Order CB1200-I Pellet Insert Service Parts and AccessoriesNbr Description 7014-083C October 26 Item No Accessories ApplianceCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceLifetime Warranty CB1200-I Pellet Insert Warranty PolicyCB1200-I Pellet Insert Telephone