Quadra-Fire CB1200I-B owner manual CB1200-I Pellet Insert Adjustable Hearth Support

Page 20

CB1200-I Pellet Insert

 

R

E. Adjustable Hearth Support

 

 

Size: 9”d x 45”w, 2” to 10” Height Adjustment

ExPLODED VIEW OF SCISSORS

 

 

Included in Kit: (1) trim top, (1) trim front, (2) trim sides,

 

 

double-sided tape (already installed)

SCREWS ARE CIRCLED

Tools Needed: Phillips head screw driver, sheet metal

 

 

shears, measuring tape, gloves

 

 

1. The 10 screws on each set of scissors will already be

DOUBLE-SIDED TAPE

DOUBLE-SIDED TAPE

loose when shipped. Figure 20.1.

Figure 20.1

 

 

 

2.Expand scissors to desired height. Tighten screws to hold in place using Phillips head screw driver. Figure 20.2.

3.Measure front and side trims to required height to cover scissors and mark pieces for cutting. Cut excess mate-

rial from top of trim’s edge, not bottom. This edge will

ExPAND SCISSORS TO DESIRED HEIGH T

 

be sharp; wear gloves to prevent injury to your hands.

 

 

Figure 20.3.

 

 

4. Using sheet metal shears, cut trim along the marked

 

 

edge. The cut edge fits under lip of top trim, so it allows

 

 

for some variance in your straight edge.

 

CUT TOP EDGE OF TRIM,

5. The double-sided tape that holds front and side trims to

INSTALL FRONT TRIM LAST.

NOT BOTTOM EDGE

CORNERS OVERLAP SIDE

 

scissors has a powerful bonding adhesive. Adjustments

TRIM PIECES

 

 

 

are extremely difficult once trim has adhered to tape. Do

Figure 20.2

 

a dry run first without removing paper from tape.

 

 

6.Place cut edge of trim under top lip and into position on scissors. Place side pieces on first and then front piece. The front piece overlaps side pieces.

7.Once you are satisfied with the positioning, remove trim

and set aside.

8. Remove the paper from double-sided tape that is to

Decorative tile

accept trim side. Align side and then press hard against

may be installed

tape to secure side piece. Repeat for other side. Install

 

front trim piece last.

 

9. There are 3 holes in the back flange of the top to secure

 

it to the wall if necessary. Use the appropriate fastener

 

for the type of wall material, i.e., brick, sheetrock, etc.

Figure 20.3

NOTE: 3/8 inch (9.5mm) thick tile or like material can be

 

cut to size and fit under lip of top trim edge for a decora-

 

tive touch. Figure 20.3.

 

WARNING

Sheet metal trim edges will be sharp.

For safety purposes wear gloves.

Injury can occur.

Page 20

7014-083C

October 26, 2006

Page 19 Page 21
Image 20
Page 19 Page 21
Contents CB1200I-B Welcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Listing and Code Approvals Design, Installation & Location Considerations Fire SafetyGetting Started Appliance LocationInspect Appliance & Components and Pre-Use Check List CB1200-I Pellet Insert Tools And Supplies NeededMeasuring Standards Dimensions and Clearances Appliance DimensionsShown with Rear Vent and Optional Outside Air Inch 0mm Clearance to Exposed Section and Face TrimFace Trim Calculating Alternate Floor Protection Material CB1200-I Pellet Insert Masonry Minimum OpeningFloor Protection Starter hole Mark area of floor to cut Vent manufacturer Install vent at clearances specified byVent Information Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCB1200-I Pellet Insert Equivalent Feet of Pipe Venting Systems CB1200-I Pellet Insert Full Reline With Outside Air Lation in a mobile home Mobile Home InstallationYou must use a Quadra-Fire Outside Air Kit for instal Rear Shroud Installation Appliance Set-UpFor Top Vent Installation Rear Vent Installation PreparationInstalling Rear Shroud Attaching Shroud to Hopper Body Adjustable Hopper Options Optional Grille InstallationTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsCB1200-I Pellet Insert Adjustable Hearth Support Size 9d x 45w, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCharred Areas in the Back Operating Instructions Fuel Size And Material General Operating InformationFuel Adjustment Control Rod Fire CharacteristicsFeed Rate Adjustment Instructions CB1200-I Pellet Insert Before Your First FireFrequently Asked Questions Do not Leave Firepot Floor OpenPossible Cause Corrective Action TroubleshootingSymptom Page Page CB10Maintaining & Servicing Your Appliance Pellet InsertCleaning Heat Exchanger Chambers Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the Glass Frequency As neededHigh Ash Fuel Content Maintenance Igniter Replacement Top frame when removing and replacing center Glass Replacing Center GlassReplacing Side Glass Ered Phillips head screw driver to remove ScrewsReference Materials Component FunctionVacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 125F Snap Disc #2 Fuel Delivery Interrupt 200FCB1200-I Pellet Insert Component Locations Exploded ViewsBeginning Manufacture Date April 8 Glass Size Center 13-7/8 wide x 11 high Glass Size SidesBeg. Manufacture Date July Item # Part Descsription, Alphabetical Order CB1200-I Pellet Insert Service Parts and AccessoriesNbr Description 7014-083C October 26 Item No Accessories ApplianceCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceLifetime Warranty CB1200-I Pellet Insert Warranty PolicyCB1200-I Pellet Insert Telephone
Top Page Image Contents