Quadra-Fire CB1200I-B CB1200-I Pellet Insert Service Parts and Accessories, Nbr Description

Page 39

R

CB1200-I Pellet Insert

D. Service Parts and Accessories

IMPORTANT: This is dated information. The most current information is located on the quadra-fire web site at www.Quadrafire.Com. When ordering, supply serial and model numbers to ensure correct part.

SCHEMATIC LIST

Nbr	Description
11	Door Frame (Black, Gold or Nickel)
12	Glass, Center
13	Glass, Side
14	Door Latch
15	Grille, Louver, Top (Black, Gold or Nickel)
16	Ashpan Door (Panel, Front Access)
17	Ashpan
18	Ash Catcher (Ash Lip)
19	Heat Exchanger Tubes
20	Power Outlet & Thermostat Block
21	Curtain, Side, Right
22	Latch, Draw (3)
23	Heat Shield Extension, Top
24	Junction Box
25	Control Box
26	Vacuum Switch
27	Hopper, Top

Nbr

Description

28Feed Motor Cover

29Feed Motor & Spring Assembly

30Heat Exchanger Cleaning Rods

31Blower, Convection

32Exhaust Adapter Assembly

33Exhaust Transition Assembly

34Blower, Exhaust

35Curtain, Side, Left

36Thermocouple Cover

37Gasket, Blower, Exhaust

38Mount, Door Hinget

39Thermocouple Holder

40Firepot Pull Rod Assembly

41Firepot, EZ Clean

42Igniter Bracket

43Igniter (Heating Element)

SERVICE PARTS

Item #

Part Descsription, Alphabetical Order

SKU

18	Ash Catcher (Ash Lip)	410-7830
17	Ash Pan	812-4130
16	Ash Pan Door (Panel, Access Front)	410-7900
	Baffle, Left	812-4200
	Baffle, Right	812-4210
31	Blower, Convection	812-4900
34	Blower, Exhaust	812-3381
	Component Pack (Includes firepot scrapper, touch-up paint, power cord & wiring harness to the	812-4330
	thermostat and manual, owner’s manual, label “Caution Fireplace Altered” warranty card, consumer’s
	view card and “How-To-Operate” DVD)
26	Control Box	SRV7000-205
28	Cover, Feed Motor, Top	410-7920
35	Curtain, Side, Left	812-4310
21	Curtain, Side, Right	812-4320
14	Door Latch Bracket	410-4912
	Exhaust Plenum Clean-Out Plate	410-7910
32	Exhaust Adapter Assembly	510-5330
33	Exhaust Transition Assembly	510-5340
	Feed Motor	812-4421
29	Feed Motor Capacitor Jumper	230-2150

October 26, 2006

7014-083C

Page 39

Image 39

Contents CB1200I-B CB1200-I Pellet Insert Welcome to the Quadra-Fire FamilyTable of Contents Listing and Code Approvals Appliance Location Design, Installation & Location ConsiderationsFire Safety Getting StartedCB1200-I Pellet Insert Tools And Supplies Needed Measuring StandardsInspect Appliance & Components and Pre-Use Check List Appliance Dimensions Dimensions and ClearancesInch 0mm Clearance to Exposed Section and Face Trim Shown with Rear Vent and Optional Outside AirFace Trim CB1200-I Pellet Insert Masonry Minimum Opening Floor ProtectionCalculating Alternate Floor Protection Material Starter hole Mark area of floor to cut Install vent at clearances specified by Vent InformationVent manufacturer Pipe Selection Chart CB1200-I Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems CB1200-I Pellet Insert Full Reline With Outside Air Mobile Home Installation You must use a Quadra-Fire Outside Air Kit for instalLation in a mobile home Appliance Set-Up Rear Shroud InstallationRear Vent Installation Preparation Installing Rear Shroud Attaching Shroud to Hopper BodyFor Top Vent Installation CB1200-I Pellet Insert Outside Air Kit Instructions Adjustable Hopper OptionsOptional Grille Installation To adjust hopperSize 9d x 45w, 2 to 10 Height Adjustment CB1200-I Pellet Insert Adjustable Hearth SupportCB1200-I Pellet Insert Panel and Trim Set Completed View CB1200-I Pellet Insert Panel and Trim Set Cont’dCharred Areas in the Back Fuel Size And Material General Operating Information Operating InstructionsCB1200-I Pellet Insert Before Your First Fire Fuel Adjustment Control RodFire Characteristics Feed Rate Adjustment InstructionsDo not Leave Firepot Floor Open Frequently Asked QuestionsTroubleshooting SymptomPossible Cause Corrective Action Page Page Pellet Insert CB10Maintaining & Servicing Your ApplianceCleaning the Glass Frequency As needed Cleaning Heat Exchanger ChambersCleaning Beneath Heat Exchanger Cleaning Exhaust PathHigh Ash Fuel Content Maintenance Igniter Replacement Ered Phillips head screw driver to remove Screws Top frame when removing and replacing center GlassReplacing Center Glass Replacing Side GlassComponent Function Reference MaterialsSnap Disc #2 Fuel Delivery Interrupt 200F Vacuum SwitchWiring Harness See .1 below Snap Disc #1 Convection Blower 125FGlass Size Center 13-7/8 wide x 11 high Glass Size Sides CB1200-I Pellet Insert Component LocationsExploded Views Beginning Manufacture Date April 8Beg. Manufacture Date July CB1200-I Pellet Insert Service Parts and Accessories Nbr DescriptionItem # Part Descsription, Alphabetical Order 7014-083C October 26 Appliance Item No AccessoriesDate of Service Performed By Description of Service CB1200-I Pellet Insert Service And Maintenance LogCB1200-I Pellet Insert Warranty Policy Lifetime WarrantyTelephone CB1200-I Pellet Insert