Quadra-Fire CB1200I-B owner manual Item No Accessories, Appliance

Page 41

R

CB1200-I Pellet Insert

Item No.

Accessories

Part No.

 

Door Assembly, Black

DR-CB12-MBK

 

Door Assembly, Gold

DR-CB12-GD

 

Door Assembly, Nickle

DR-CB12-NL

 

Floor Protector

811-0730

 

Grille, Louver, Black

LVGRL-CB12-MBK

 

Grille, Louver, Gold

LVGRL-CB12-GD

 

Grille, Louver, Nickel

LVGRL-CB12-NL

 

Log Set, 3 pieces

811-0592

 

Outside Air Kit

811-0700

 

Panel & Trim Set, Small, 30” h x 40” w, Gold

SP-CB12I3040-GD

 

Panel & Trim Set, Small, 30” h x 40” w, Nickel

SP-CB12I3040-NL

 

Panel & Trim Set, Large, 33” h x 50” w, Gold

SP-CB12I3350-GD

 

Rear Shroud Kit

811-0680

 

Rear Top Vent Kit

811-0690

 

Top Vent Kit, Rear Shroud

811-0650

 

Top Vent Adapter, 3 inch

811-0660

 

Top Vent Adapter, 4 inch

811-0670

 

Thermostat, Mechanical

812-3760

 

Thermostat, Programmable #9600

811-0520

 

Vent Adapter, 3 inch to 4 inch

811-0720

 

Zero Clearance Adjustable Trim Support, 2 inch to 10 inch

841-1000

Appliance

CB1200-I Insert, No Door or Grille (order door & grille separately)

Part No.

CB1200I-B

October 26, 2006

7014-083C

Page 41

Image 41
Contents CB1200I-B CB1200-I Pellet Insert Welcome to the Quadra-Fire FamilyTable of Contents Listing and Code Approvals Fire Safety Design, Installation & Location ConsiderationsGetting Started Appliance LocationInspect Appliance & Components and Pre-Use Check List CB1200-I Pellet Insert Tools And Supplies NeededMeasuring Standards Appliance Dimensions Dimensions and ClearancesInch 0mm Clearance to Exposed Section and Face Trim Shown with Rear Vent and Optional Outside AirFace Trim Calculating Alternate Floor Protection Material CB1200-I Pellet Insert Masonry Minimum OpeningFloor Protection Starter hole Mark area of floor to cut Vent manufacturer Install vent at clearances specified byVent Information Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCB1200-I Pellet Insert Equivalent Feet of Pipe Venting Systems CB1200-I Pellet Insert Full Reline With Outside Air Lation in a mobile home Mobile Home InstallationYou must use a Quadra-Fire Outside Air Kit for instal Appliance Set-Up Rear Shroud InstallationFor Top Vent Installation Rear Vent Installation PreparationInstalling Rear Shroud Attaching Shroud to Hopper Body Optional Grille Installation Adjustable Hopper OptionsTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsSize 9d x 45w, 2 to 10 Height Adjustment CB1200-I Pellet Insert Adjustable Hearth SupportCB1200-I Pellet Insert Panel and Trim Set Completed View CB1200-I Pellet Insert Panel and Trim Set Cont’dCharred Areas in the Back Fuel Size And Material General Operating Information Operating InstructionsFire Characteristics Fuel Adjustment Control RodFeed Rate Adjustment Instructions CB1200-I Pellet Insert Before Your First FireDo not Leave Firepot Floor Open Frequently Asked QuestionsPossible Cause Corrective Action TroubleshootingSymptom Page Page Pellet Insert CB10Maintaining & Servicing Your ApplianceCleaning Beneath Heat Exchanger Cleaning Heat Exchanger ChambersCleaning Exhaust Path Cleaning the Glass Frequency As neededHigh Ash Fuel Content Maintenance Igniter Replacement Replacing Center Glass Top frame when removing and replacing center GlassReplacing Side Glass Ered Phillips head screw driver to remove ScrewsComponent Function Reference MaterialsWiring Harness See .1 below Vacuum SwitchSnap Disc #1 Convection Blower 125F Snap Disc #2 Fuel Delivery Interrupt 200FExploded Views CB1200-I Pellet Insert Component LocationsBeginning Manufacture Date April 8 Glass Size Center 13-7/8 wide x 11 high Glass Size SidesBeg. Manufacture Date July Item # Part Descsription, Alphabetical Order CB1200-I Pellet Insert Service Parts and AccessoriesNbr Description 7014-083C October 26 Appliance Item No AccessoriesDate of Service Performed By Description of Service CB1200-I Pellet Insert Service And Maintenance LogCB1200-I Pellet Insert Warranty Policy Lifetime WarrantyTelephone CB1200-I Pellet Insert