Quadra-Fire CB1200I-B owner manual Mobile Home Installation, Lation in a mobile home

Page 16

CB1200-I Pellet Insert

 

R

 

 

 

 

 

 

 

 

 

 

 

6

Mobile Home

 

 

 

 

 

 

 

A. Mobile Home Installation

 

 

 

CAUTION

 

 

You must use a Quadra-Fire Outside Air Kit for instal-

 

 

Maintain structural integrity of mobile home:

 

 

lation in a mobile home.

 

 

• Floor, wall, ceiling and/or roof.

 

 

 

 

 

 

1. An outside air inlet must be provided for the combustion

Do NOT cut through:

 

 

• Floor joist, wall studs or ceiling trusses.

 

 

air and must remain clear of leaves, debris, ice and/or

 

 

• Any supporting material that would affect the structural

 

 

snow. It must be unrestricted while the appliance is

 

 

integrity.

 

 

in use to prevent room air starvation which causes

 

 

 

 

 

smoke spillage. Smoke spillage can also set off smoke

 

 

 

alarms.

 

 

 

2.The combustion air duct system must be made of metal. It must permit zero clearance to combustible construction and prevent material from dropping into the inlet or into the area beneath the dwelling and contain a rodent screen.

3.The appliance must be secured to the mobile home structure by bolting it to the floor (using lag bolts). Use the same holes that secured the appliance to the ship- ping pallet.

4.The appliance must be grounded with #8 solid copper grounding wire or equivalent, terminated at each end with an NEC approved grounding device.

5.Refer to Clearances to Combustibles and floor pro- tection requirements on pages 8 & 9 for listings to combustibles and appropriate chimney systems.

6.Use silicone to create an effective vapor barrier at the location where the chimney or other component penetrates to the the exterior of the structure.

7.Follow the chimney manufacturer’s instructions when installing the vent system for use in a mobile home.

8.Installation shall be in accordance with the Manufactur- ers Home & Safety Standard (HUD) CFR 3280, Part 24.

 

Spark Arrestor Cap

Storm Collar

 

 

Roof Flashing

Joist Shield/Firestop

Double Wall

 

 

Pellet Vent

Figure 16.1

WARNING

Installation must comply with Manufactured Home and Safety Standard (HUD), CFR 3280, Part 24.

WARNING

Never install in a sleeping room.

Page 16

7014-083C

October 26, 2006

Page 15 Page 17
Image 16
Page 15 Page 17
Contents CB1200I-B Welcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Listing and Code Approvals Design, Installation & Location Considerations Fire SafetyGetting Started Appliance LocationMeasuring Standards CB1200-I Pellet Insert Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List Dimensions and Clearances Appliance DimensionsShown with Rear Vent and Optional Outside Air Inch 0mm Clearance to Exposed Section and Face TrimFace Trim Floor Protection CB1200-I Pellet Insert Masonry Minimum OpeningCalculating Alternate Floor Protection Material Starter hole Mark area of floor to cut Vent Information Install vent at clearances specified byVent manufacturer CB1200-I Pellet Insert Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems CB1200-I Pellet Insert Full Reline With Outside Air You must use a Quadra-Fire Outside Air Kit for instal Mobile Home InstallationLation in a mobile home Rear Shroud Installation Appliance Set-UpInstalling Rear Shroud Attaching Shroud to Hopper Body Rear Vent Installation PreparationFor Top Vent Installation Adjustable Hopper Options Optional Grille InstallationTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsCB1200-I Pellet Insert Adjustable Hearth Support Size 9d x 45w, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCharred Areas in the Back Operating Instructions Fuel Size And Material General Operating InformationFuel Adjustment Control Rod Fire CharacteristicsFeed Rate Adjustment Instructions CB1200-I Pellet Insert Before Your First FireFrequently Asked Questions Do not Leave Firepot Floor OpenSymptom TroubleshootingPossible Cause Corrective Action Page Page CB10Maintaining & Servicing Your Appliance Pellet InsertCleaning Heat Exchanger Chambers Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the Glass Frequency As neededHigh Ash Fuel Content Maintenance Igniter Replacement Top frame when removing and replacing center Glass Replacing Center GlassReplacing Side Glass Ered Phillips head screw driver to remove ScrewsReference Materials Component FunctionVacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 125F Snap Disc #2 Fuel Delivery Interrupt 200FCB1200-I Pellet Insert Component Locations Exploded ViewsBeginning Manufacture Date April 8 Glass Size Center 13-7/8 wide x 11 high Glass Size SidesBeg. Manufacture Date July Nbr Description CB1200-I Pellet Insert Service Parts and AccessoriesItem # Part Descsription, Alphabetical Order 7014-083C October 26 Item No Accessories ApplianceCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceLifetime Warranty CB1200-I Pellet Insert Warranty PolicyCB1200-I Pellet Insert Telephone
Top Page Image Contents