Quadra-Fire QV32-A, QV36-A manual DV-FLEX-10

Page 14

6 5/32” (156mm)

7 3/8”		5 7/8”
(187mm)		(149mm)

85/8”

(220mm)

DV-90D

8 1/2”	11 5/8”
(216mm)	(295mm)

11 1/16” (281mm)

1115/16”

(303mm)

67/16”

(164mm)

8 1/2” (216mm)

	6 1/2”	5 1/16”
	(165mm)
		(129mm)

8 5/8” (220mm)

DV-45D

DV-48D

DV-36D

DV17/24D

DV-12/17D

473/4”

(1.2m)

DV-FLEX-10

353/4”

(908mm)

DV-06D

53/4”

(146mm)

12-17

(305-432mm)

17-24

(432-610mm)

	8 3/4”	11 3/4”
	8 3/4”	(298mm)
	(222mm)	(298mm)
	(222mm)
DV-09D		DV-12D

DV-FLEX-5

60”

(1524mm)

DV-FLEX-3

36”

(914mm)

120” (3048mm)

DV-FLEX-2

24”

(610mm)

NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) AT EACH JOINT.

Figure 6. D-Series Direct Vent Component Specifications (5-inch inner pipe / 8 5/8-inch outer pipe)

14

Image 14

Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Service Parts Accessories / Accessoires Standing Pilot Ignition / D’ALLUMAGE PAR VeilleuseLog Set Assembly DF-36TS-BK Appliance Certification Installation CodesHigh Altitude Installations CertificationANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Village Collection Gas Fireplaces Diagram of the QV36-A Diagram of the QV-32-A Clearance Requirements Constructing the Fireplace ChaseLocating the Fireplace Framing Dimensions Framing the FireplaceDV-FLEX-10 47 3/4 Vent System Approvals Installing the Vent SystemIdentifying Vent Components Use D-Series components only Straight UP Vertical VentingUse SL D-Series components only Use SL D-Series components only Venting with Two 90 Elbows Natural GAS MAX. = 16 FT 4.8m V + V1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H Venting with Four 90 elbows SET of Collars YOU are Using could Cause a Fire Adding Venting Components Install Support Brackets Continue Adding Vent ComponentsCeiling Firestop Ceiling Side 191mm Vent TerminationPositioned SO That the Arrow is Pointing UP Minimum Trapezoid CAP TerminationVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Standing Pilot Ignition System Positioning, Leveling, and Securing the FireplaceGas Control System To Check for GAS Leaks Gas Supply LineGas Pressure Requirements PressureOptional Accessories Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Wall SwitchRefractory Kit Placement BRICK-291, BRICK-293 FinishingInstalling Trim, Logs Ember Material Glass SpecificationsDouble-check for faulty components Before Lighting the FireplaceStanding Pilot Ignition After the InstallationLighting the Appliance What to do if YOU Smell GASFireplace Maintenance Important Turn OFF the GAS Before Servicing Your FireplaceTroubleshooting Be Placed in this Opening Lifetime Warranty