Quadra-Fire QV36-A, QV32-A manual Table of Contents

Page 3

TABLE OF CONTENTS
Safety and Warning Information		2
uService Parts Lists		4
Section 1: Approvals and Codes		8
Appliance Certification		8
Installation Codes		8
High Altitude Installations		8
Section 2: Getting Started		9
Introducing the Village Collection Gas Fireplaces		9
u Pre-installation Preparation		9
Section 3: Installing the Fireplace		12
Constructing the Fireplace Chase		12
u Step 1	Locating the Fireplace	12
Step 2	Framing the Fireplace	13
Step 3	Installing the Vent System	16
	A. Vent System Approvals	16
	B. Installing Vent Components	26
	u C. Vent Termination	29
Step 4	Positioning, Leveling, and
	Securing the Fireplace	32
Step 5	The Gas Control Systems	32
Step 6	The Gas Supply Line	33
Step 7	Gas Pressure Requirements	33
Step 8	Wiring the Fireplace	34
Step 9	Finishing	35
	Refractory Kit Placement	35
Step 10	Installing Trim, Logs, and Ember Material	36
	Installing the Trim	36
	Shutter Settings	36
	Placing the Ember Material	36
Step 11	Before Lighting the Fireplace	37
Step 12	Lighting the Appliance	38
After the Installation		38
Section 4: Maintaining and Servicing Your Fireplace		39
Section 5: Troubleshooting		40
Limited Lifetime Warranty		42
u = Contains updated information.

3

Image 3

Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents Service Parts Standing Pilot Ignition / D’ALLUMAGE PAR Veilleuse Accessories / AccessoiresLog Set Assembly DF-36TS-BK Certification Installation CodesHigh Altitude Installations Appliance CertificationPre-install Preparation Introducing the Village Collection Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the QV36-A Diagram of the QV-32-A Constructing the Fireplace Chase Locating the FireplaceClearance Requirements Framing the Fireplace Framing DimensionsDV-FLEX-10 47 3/4 Installing the Vent System Identifying Vent ComponentsVent System Approvals Straight UP Vertical Venting Use SL D-Series components onlyUse D-Series components only Use SL D-Series components only Venting with Two 90 Elbows Natural GAS MAX. = 16 FT 4.8m V + V1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H Venting with Four 90 elbows SET of Collars YOU are Using could Cause a Fire Continue Adding Vent Components Adding Venting Components Install Support BracketsCeiling Firestop Ceiling Side Minimum Trapezoid CAP Termination Vent TerminationPositioned SO That the Arrow is Pointing UP 191mmVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Fireplace Gas Control SystemStanding Pilot Ignition System Pressure Gas Supply LineGas Pressure Requirements To Check for GAS LeaksWall Switch Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Optional AccessoriesFinishing Refractory Kit Placement BRICK-291, BRICK-293Glass Specifications Installing Trim, Logs Ember MaterialBefore Lighting the Fireplace Double-check for faulty componentsWhat to do if YOU Smell GAS After the InstallationLighting the Appliance Standing Pilot IgnitionImportant Turn OFF the GAS Before Servicing Your Fireplace Fireplace MaintenanceTroubleshooting Be Placed in this Opening Lifetime Warranty