Quadra-Fire QV32-A, QV36-A manual Natural GAS

Page 20

VENTING WITH TWO (2) 90o ELBOWS

NATURAL GAS

V (MIN.)

 

H + H1 (MAX.)

90o Elbow on Top

2 FT (610mm)

1 FT (305mm)

 

3 FT (914mm)

2 FT (610mm)

 

4 FT (1.22m)

3 FT (914mm)

 

6 FT (1.86m)

4 FT (1.22m)

 

8 FT (2.48m)

5 FT (1.52m)

 

16 FT (4.8m)

H + H1 MAX. = 16 FT (4.8m)

V + H + H1

MAX. = 40 FT (12.2m)

VENTING WITH TWO (2) 90o ELBOWS

PROPANE

V (MIN.)

H + H1 (MAX.)

90o Elbow on Top

NOT ALLOWED

1 FT (305mm)

2 FT (610mm)

 

2 FT (610mm)

4 FT (1.22m)

 

3 FT (914mm)

6 FT (1.86m)

 

4 FT (1.22m)

8 FT (2.48m)

 

5 FT (1.52m)

16 FT (4.8m)

 

H + H1 MAX. = 16 FT (4.8m)

V + H + H1 MAX. = 40 FT (12.2m)

H1

H

Note: There MUST be a 25% reduction in total H when using flex vent, except when using the simple up and out installation (see Figure 9).

Use SL D-Series components only.

Figure 15. Venting with Two 90° Elbows

V

20

Image 20
Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Service Parts Accessories / Accessoires Standing Pilot Ignition / D’ALLUMAGE PAR VeilleuseLog Set Assembly DF-36TS-BK Installation Codes High Altitude InstallationsAppliance Certification CertificationANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Village Collection Gas Fireplaces Diagram of the QV36-A Diagram of the QV-32-A Clearance Requirements Constructing the Fireplace ChaseLocating the Fireplace Framing Dimensions Framing the FireplaceDV-FLEX-10 47 3/4 Vent System Approvals Installing the Vent SystemIdentifying Vent Components Use D-Series components only Straight UP Vertical VentingUse SL D-Series components only Use SL D-Series components only Venting with Two 90 Elbows Natural GAS MAX. = 16 FT 4.8m V + V1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H Venting with Four 90 elbows SET of Collars YOU are Using could Cause a Fire Adding Venting Components Install Support Brackets Continue Adding Vent ComponentsCeiling Firestop Ceiling Side Vent Termination Positioned SO That the Arrow is Pointing UP191mm Minimum Trapezoid CAP TerminationVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Standing Pilot Ignition System Positioning, Leveling, and Securing the FireplaceGas Control System Gas Supply Line Gas Pressure RequirementsTo Check for GAS Leaks PressureWiring the Fireplace For Standing Pilot Ignition Wiring Appliance RequirementsOptional Accessories Wall SwitchRefractory Kit Placement BRICK-291, BRICK-293 FinishingInstalling Trim, Logs Ember Material Glass SpecificationsDouble-check for faulty components Before Lighting the FireplaceAfter the Installation Lighting the ApplianceStanding Pilot Ignition What to do if YOU Smell GASFireplace Maintenance Important Turn OFF the GAS Before Servicing Your FireplaceTroubleshooting Be Placed in this Opening Lifetime Warranty