Quadra-Fire QV32-A, QV36-A manual Venting with Three 90 elbows

Page 22

V	H	H + H1
1' MIN. (305 mm)	2' MAX. (610mm)	4' MAX. (1.22m)
2' MIN. (610 mm)	4' MAX. (1.22m)	8' MAX. (2.48m)
3' MIN. (914 mm)	6' MAX. (1.86m)	12' MAX. (3.72m)
4' MIN. (1.22 m)	8' MAX. (2.48m)	16' MAX. (4.8m)

V1+V+H+H1 = 40' MAX. (12.4m)

H = 8' MAX. (2.48m) H+H1 =16' MAX. (4.8m)

V1

V

H

H1

	V		H	H + H1 + H2
1' MIN. (305 mm)			2' MAX. (610 mm)	4' MAX. (1.22m)
	2' MIN. (610 mm)		4' MAX. (1.22 m)	8' MAX. (2.48m)
	3' MIN. (914 mm)		6' MAX. (1.86 m)	12' MAX. (3.72m)
	4' MIN. (1.22 m)		8' MAX. (2.48 m)	16' MAX. (4.8m)
	V+H+H +H = 40' MAX. (12.4 m)
	1	2
	H = 8' MAX. (2.48m)		H + H1 + H2 = 16' MAX. (4.8m)

H2

Use D-Series

H1

components only.

Note: There MUST be a 25% reduction in total H when using flex vent, except when using the simple up and out installation (see Figure 9).

Figure 17. Venting with Three 90° elbows

22

V

H

Image 22

Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Service Parts Accessories / Accessoires Standing Pilot Ignition / D’ALLUMAGE PAR VeilleuseLog Set Assembly DF-36TS-BK Appliance Certification Installation CodesHigh Altitude Installations CertificationIntroducing the Village Collection Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the QV36-A Diagram of the QV-32-A Locating the Fireplace Constructing the Fireplace ChaseClearance Requirements Framing Dimensions Framing the FireplaceDV-FLEX-10 47 3/4 Identifying Vent Components Installing the Vent SystemVent System Approvals Use SL D-Series components only Straight UP Vertical VentingUse D-Series components only Use SL D-Series components only Venting with Two 90 Elbows Natural GAS MAX. = 16 FT 4.8m V + V1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H Venting with Four 90 elbows SET of Collars YOU are Using could Cause a Fire Adding Venting Components Install Support Brackets Continue Adding Vent ComponentsCeiling Firestop Ceiling Side 191mm Vent TerminationPositioned SO That the Arrow is Pointing UP Minimum Trapezoid CAP TerminationVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Gas Control System Positioning, Leveling, and Securing the FireplaceStanding Pilot Ignition System To Check for GAS Leaks Gas Supply LineGas Pressure Requirements PressureOptional Accessories Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Wall SwitchRefractory Kit Placement BRICK-291, BRICK-293 FinishingInstalling Trim, Logs Ember Material Glass SpecificationsDouble-check for faulty components Before Lighting the FireplaceStanding Pilot Ignition After the InstallationLighting the Appliance What to do if YOU Smell GASFireplace Maintenance Important Turn OFF the GAS Before Servicing Your FireplaceTroubleshooting Be Placed in this Opening Lifetime Warranty