Quadra-Fire QF130 owner manual Fan Wiring with Remote, AUX 300 Module FAN WHT GRN BLK Blowers

Page 27

D. Fan Wiring with Remote

This appliance may be used with an RC200 or RC300 remote control. See Figure 10.3.

1.Remove cord assembly spades from rheostat and sensor switch.

NOTICE: Fan speed and operation are controlled by the remote control. The sensor switch and rheostat are no longer needed.

2.Plug two cord assembly spade connectors together.

3.Unplug fan cord assembly from standard cord assembly.

4.Plug fan cord assembly into AUX300 module.

5.Plug AUX300 module into the standard cord assembly.

E.Control Module Operation

See Section 2.H for control module operation instructions.

NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 1050 C RATED WIRE.

NOTE: USE ZIP TIES TO RESTRAIN THE LOOSE WIRES UNDERNEATH THE APPLIANCE AND KEEP THEM AWAY FROM THE BLOWER WHEEL (FAN BLADES).

BLOWER	PLUG
BLOWER	120V EXISTING	STEP 5
	OUTLET	STEP 5

		STEPS
		1 & 2
		STEPS
		3 & 4
		SENSOR SWITCH
	WHT (2)
	GRN (2)
	BLK (2)
	BLK (2)	SPEED CONTROL
	GRN (2)	SPEED CONTROL
	GRN (2)	(RHEOSTAT)
	BLK (2)

NOTE: SENSOR SWITCH AND RHEOSTAT SPEED CONTROL MUST BE REMOVED FROM CIRCUIT IF SYSTEM IS CONTROLLED WITH RC200/RC300 REMOTE.

PLUG INTO 120V

EXISTING OUTLET

DC REGULATOR

RECEPTICLE

TO CONTROL

MODULE

BLK

BLK

BLOWER RECEPTICLE

AUX 300 MODULE

FAN

WHT

GRN

BLK

BLK

GRN

WHT

BLK

GRN

BLK

BLOWERS

BLK

GRN

BLK

Figure 10.3 Wiring Diagram - Fan with RC200/RC300 Remote

Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11

27

Image 27

Contents Models What to do if you smell gasHOT Surfaces Congratulations Homeowner Reference InformationXxxxxxxx User Guide Table of ContentsLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches IPI Battery Tray/Battery InstallationModule Reset Control Module OperationBefore Lighting Fireplace GAS Valve Lighting Instructions IPIFinal inspection by What to do if YOU Smell GASFrequently Asked Questions Issue SolutionsAfter Appliance is Lit Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection VentingIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components QFI35 QFI30 Fireplace Size RequirementsMinimum Fireplace Opening Minimum Fireplace SizeSide View TOP View Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Vent LimitsIPI Models Placing, Securing and Leveling the Appli- anceDamper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningGas Connection Gas InformationFuel Conversion Gas PressureElectrical Information Wiring RequirementsIntelliFire Plus Ignition System Wiring ON/OFF SwitchBLK Optional Accessories RequirementsAUX 300 Module FAN WHT GRN BLK Blowers Fan Wiring with RemoteClearances to Mantels or other Combustibles above Appliance FinishingAppliance Setup Install the Log Assembly Log Set Assembly LOGS-QFI30 Models QFI30Mates With Slot Mate Notch With Grate BAR For LOG #6Slot Install Back Refractory Log Set Assembly LOGS-QFI35 Models QFI35Slot on Log #2 LOG Slot Mate LOG Pins with LOG Slots Flat Spot For LOG #6 Air Shutter Setting Air Shutter SettingsQFI30 QFI35 Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System To remove any contaminants that may have accumulated on ﬂame Appliance Dimension Diagram Model DimensionsReference Materials Direct Vent Flex Liner Kits Vent Kits ComponentsContact Information