Quadra-Fire QF130 owner manual Reference Materials, Appliance Dimension Diagram, Model Dimensions

Page 39

14 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only.

F

	A
H	O
	O
Q
R
	P

T

B

C

E

J

GAS LINE							K


ACCESS
	L
	L

S

G

D

ELECTRICAL

ACCESSN

I

M

MODEL DIMENSIONS

	Location	QFI35		QFI30
	Location	Inches	Millimeters	Inches	Millimeters
		Inches	Millimeters	Inches	Millimeters
	A	23-1/2	597	20-3/16	513
	B	34-5/8	879	30-1/2	775

	C	31-9/16	802	27-7/16	697

	D	15-11/16	398	12-13/16	325
	E	24	610	20-1/2	521
	F	21-1/16	535	17-5/8	448

	G*	15-7/8	403	14-5/8	372

	H	11-3/4	298	10-1/8	257
	I	20-3/8	518	17	432
	J	1-3/4	44	1-3/4	44

MODEL DIMENSIONS

Location	QFI35			QFI30
Location	Inches	Millimeters	Inches		Millimeters
	Inches	Millimeters	Inches		Millimeters
K	4-13/16	122	4-13/16		122
L	10-1/16	256	9		229

M	2-1/4	57	2-1/4		57

N	5	127	3-15/16		100
O	5-1/8	130	5-3/16		132
P	8	203	8		203

Q	1-13/16	46	1-3/4		44

R	2-1/4	57	2-1/4		57
S	4-13/16	122	4-7/16		113
T	10-1/2	267	9-1/2		241

*Note: Location G on Figure 14.1 is measuring the appliance depth, for installation depth reference Location G on Figure 5.1.

Figure 14.1 Appliance Dimensions

Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11

39

Image 39

Contents Models What to do if you smell gasHOT Surfaces Congratulations Homeowner Reference InformationXxxxxxxx User Guide Table of ContentsLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches IPI Battery Tray/Battery InstallationModule Reset Control Module OperationBefore Lighting Fireplace GAS Valve Lighting Instructions IPIFinal inspection by What to do if YOU Smell GASFrequently Asked Questions Issue SolutionsAfter Appliance is Lit Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection VentingIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components QFI35 QFI30 Fireplace Size RequirementsMinimum Fireplace Opening Minimum Fireplace SizeSide View TOP View Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Vent LimitsIPI Models Placing, Securing and Leveling the Appli- anceDamper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningGas Connection Gas InformationFuel Conversion Gas PressureElectrical Information Wiring RequirementsIntelliFire Plus Ignition System Wiring ON/OFF SwitchBLK Optional Accessories RequirementsAUX 300 Module FAN WHT GRN BLK Blowers Fan Wiring with RemoteClearances to Mantels or other Combustibles above Appliance FinishingAppliance Setup Install the Log Assembly Log Set Assembly LOGS-QFI30 Models QFI30Mates With Slot Mate Notch With Grate BAR For LOG #6Slot Install Back Refractory Log Set Assembly LOGS-QFI35 Models QFI35Slot on Log #2 LOG Slot Mate LOG Pins with LOG Slots Flat Spot For LOG #6 Air Shutter Setting Air Shutter SettingsQFI30 QFI35 Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System To remove any contaminants that may have accumulated on ﬂame Appliance Dimension Diagram Model DimensionsReference Materials Direct Vent Flex Liner Kits Vent Kits ComponentsContact Information