Honeywell VISTA-40, 2-Partitioned Security System manual Table of Contents

Page 2

Table of Contents

Recommended Programming Procedure

3

Device Programming

21

Program Field Index

4

Relay Programming

22

VISTA-40 Programming Form

5

Relay Voice Descriptors

25

Partition-Specific Fields

9

Relay Voice Descriptors and Custom Word

 

Programming With #93 Menu Mode

10

Substitutes Vocabulary

26

Custom Word Substitutes for VIP Module

 

Zone Programming

11

 

Annunciation

26

5800 Series Transmitters Loop Designations

13

System Layout Worksheets

27

Expert Mode Zone Programming

14

Relay Outputs Worksheets

33

Alpha Descriptors Programming

17

VISTA-40 Summary of Connections Diagram

35

Alpha Descriptor Vocabulary

20

 

 

The purpose of this document is to provide a quick and easy way to program your entire system. A recommended programming procedure is included, followed by a list of program fields with the corresponding program group they belong to (system-wide, partition-specific, scheduling, etc.). Two program forms are included. One contains all the programming fields, and the other contains the partition-specific fields. If you are setting up a single-partition system, the partition-specific fields become system-wide fields.

Following the program forms are system layout worksheets. We recommend that you use these sheets to plan your system before programming is performed. If you need further information about specific programming options, see the ADEMCO VISTA-40 Installation and Setup Guide.

Make sure that one two-line alpha keypad is connected to the control and is set to device address "00."

Single-Partition System

The system default is for a single-partition system. Use the VISTA-40 SINGLE PARTITION PROGRAMMING FORM when programming for single-partition usage. Follow the steps outlined in RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure.

Multiple-Partition System

You must enter the number of partitions you are using in data field 2*00 to set the system for multiple partitions. Use the VISTA-40 SINGLE PARTITION and the PARTITION-SPECIFIC PROGRAM FORMS when programming the system for multiple partitions. Follow the steps outlined in RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure.

SUMMARY OF PROGRAMMING COMMANDS

•To enter program mode, enter installer code + [8] + [0] + [0]

•To set standard defaults, press ✱97

•To change to next page of program fields, press ✱94

•To return to previous set of fields, press ✱99

•To erase account and phone number field entries, press [✱] + field number + [✱]

•To assign zone descriptors, press #93 + follow menu prompts

•To add custom words, press #93 + follow menu prompts

•To enter Installer's Message, press #93 + follow menu prompts

•To exit program mode, enter ✱99 OR ✱98: ✱99 allows re-access to programming mode by installer code. ✱98 prevents re-access to programming mode by installer code.

Standard default (✱97) values are shown in brackets [ ], otherwise default = 0.

– 2 –

Page 1 Page 3
Image 2
Page 1 Page 3
Contents $0&29,67$ N7001PRV5 5/04 Rev aTable of Contents Recommended Programming Procedure Field Group Program Field IndexField Group VISTA-40 Programming Form 54 *57 Alarm Report Codes & ID Digits for Zones Enable OPEN/CLOSE Report forOPEN/CLOSE Report for Keyswitch 59 *62 Alarm Report Codes & ID Digits for ZonesFields 1*28 1*31 are not applicable for UL installations 2nd Page Programming Fields press *943rd Page Programming Fields press *94 1st Page Fields Partition-Specific FieldsPartition # Program Fields 2nd Page FieldsProgramming With #93 Menu Mode Enter Zone no = Quit Zone ProgrammingSET to CONFIRM? = YES Zone Type PERIMETER03Input S/N Input TypeInput S/N AXXX-XXXX Series Transmitters Loop Designations Xmit to Confirm Press to SkipEnter Zone no Expert Mode Zone ProgrammingProgram field 200 Number of Partitions SET to CONFIRM?Input S/N XXX-XXXX From TemplateTemplate Loop Function Wireless Key Default Templates 58045804BD Zone Type Template Loop FunctionAlpha Descriptors Programming Zone DESCRIP? Default SCREEN? Custom WORD? Part DESCRIP?Zone Descriptors Select Zone Descriptor mode Exit Edit MODE?Accept the word Select Default Screen modeSelect Custom Word Mode Select the next wordEnter the custom word number 01-20 you want to create Type the word using one of two methods as followsFollow the same procedure as for custom words Save the word by pressingCharacter Ascii Chart Alpha Descriptor VocabularyRF Expander Device ProgrammingAlpha Keypad VIP ModuleRelay Programming AlarmFault TroubleEnter Relay # Relay Output Devices ProgrammingChoices for Start/Stop Zone Types and System Operations Relay Action No Response Start Event Not UsedRelay Type Plex ECP Address Module RELAY# House Code Zone List ProgrammingStart Partn ANY Partition Unit CodeRelay Voice Descriptors Custom Word Substitutes for VIP Module Annunciation Custom Word no =QUIT Enter Index #System Layout Worksheets Descriptor Prim Partition # Char max Sub. #Access Codes & User Definitions for Partitions 1 DefaultsZone Definition for Zones Zone Definition for Zones Zone Definition for Zones Zone Types Zone Definitions for Keypad Panic Zones 95, 96Zone Definitions for System Zones 70, 88 89, 90, 91 Input TypesRelay Outputs Worksheets Choices for System Operation arePage Ademco VISTA-40 Summary of Connections GroundEileen Way, Syosset, New York
Top Page Image Contents