Honeywell 2-Partitioned Security System Device Programming, Alpha Keypad, RF Expander, VIP Module

Page 21

Device Programming

This menu is used to program keypads, receivers, and relay modules, etc.

Device Address 00 is always set as an alpha keypad assigned to Partition 1 with no sounder suppression options, and these settings cannot be changed.

From Data Field Programming mode, press [#]93 to display "ZONE PROG?" Press 0 repeatedly to display "DEVICE PROG?"

PROMPTEXPLANATION

 

DEVICE PROG?

 

 

1=YES 0=NO

0

 

 

 

 

 

 

 

 

DEVICE ADDRESS

 

 

01-15, 00=QUIT

01

 

 

 

 

 

 

 

DEVICE TYPE

0

Press 1 to enter Device Programming.

The device address identifies the device to the control. Enter the 2-digit device address number to match the device’s physical address setting (01-15).

NOTE: If using the 4285/4286 Voice Module, it must be used at Device Address 04.

Select the type of addressable device as follows:

0

= device not used

3

= RF receiver (5881)

1

= alpha keypad (6139/6160)

4

= output relay module (4204)

2

= fixed keypad (6137/6150)

5

= voice (VIP) Module (4285/4286)

Press [✱] to accept entry.

Alpha Keypad

PROMPTEXPLANATION

01 CONSOLE PART.

1

01 SOUND OPTION

00

If you selected device type 1 (alpha keypad) or 2 (fixed keypad), this prompt appears. Enter the addressable device’s default partition number (1 to maximum number of partitions programmed for system in field 2*00). This is the primary partition for the device.

Press [✱] to accept entry.

Keypads can be individually programmed to suppress arm/disarm beeps, entry/exit beeps and chime mode beeps. This helps prevent unwanted sounds from disturbing users in other areas of the premises.

Enter a number 00-03for the keypad sounding suppression options desired for the keypad as follows: 00 = no suppression

01 = suppress arm/disarm & entry/exit beeps

02 = suppress chime mode beeps only

03 = suppress arm/disarm, entry/exit and chime mode beeps Press [✱] to accept entry.

RF Expander

PROMPTEXPLANATION

01 RF EXPANDER

 

HOUSE ID

00

If you selected device type 3 (RF receiver), this prompt appears. Enter the 2-digit House ID (00-31). This is required if you are using a wireless keypad (5827/5827BD).

Press [✱] to accept entry.

VIP Module

PROMPTEXPLANATION

01 MODULE PART.

1

If you selected device type 5 (VIP Module), this prompt appears. Enter the partition number 1-2in which the module is located.

Press [✱] to accept entry.

Press 00 + [✱] to exit Menu mode. Press ✱99 to exit Program mode.

– 21 –

Page 20 Page 22
Image 21
Page 20 Page 22
Contents N7001PRV5 5/04 Rev a $0&29,67$Table of Contents Recommended Programming Procedure Program Field Index Field GroupField Group VISTA-40 Programming Form OPEN/CLOSE Report for Keyswitch Enable OPEN/CLOSE Report for54 *57 Alarm Report Codes & ID Digits for Zones 59 *62 Alarm Report Codes & ID Digits for Zones2nd Page Programming Fields press *94 Fields 1*28 1*31 are not applicable for UL installations3rd Page Programming Fields press *94 Partition # Program Fields Partition-Specific Fields1st Page Fields 2nd Page FieldsProgramming With #93 Menu Mode SET to CONFIRM? = YES Zone ProgrammingEnter Zone no = Quit Zone Type PERIMETER03Input Type Input S/N AXXX-XXXXInput S/N Xmit to Confirm Press to Skip Series Transmitters Loop DesignationsProgram field 200 Number of Partitions Expert Mode Zone ProgrammingEnter Zone no SET to CONFIRM?From Template Input S/N XXX-XXXX5804BD Wireless Key Default Templates 5804Template Loop Function Zone Type Template Loop FunctionZone Descriptors Select Zone Descriptor mode Zone DESCRIP? Default SCREEN? Custom WORD? Part DESCRIP?Alpha Descriptors Programming Exit Edit MODE?Select Custom Word Mode Select Default Screen modeAccept the word Select the next wordFollow the same procedure as for custom words Type the word using one of two methods as followsEnter the custom word number 01-20 you want to create Save the word by pressingAlpha Descriptor Vocabulary Character Ascii ChartAlpha Keypad Device ProgrammingRF Expander VIP ModuleFault AlarmRelay Programming TroubleChoices for Start/Stop Zone Types and System Operations Relay Output Devices ProgrammingEnter Relay # Relay Action No Response Start Event Not UsedStart Partn ANY Partition Zone List ProgrammingRelay Type Plex ECP Address Module RELAY# House Code Unit CodeRelay Voice Descriptors Custom Word no =QUIT Enter Index # Custom Word Substitutes for VIP Module AnnunciationDescriptor Prim Partition # Char max Sub. # System Layout WorksheetsDefaults Access Codes & User Definitions for Partitions 1Zone Definition for Zones Zone Definition for Zones Zone Definition for Zones Zone Definitions for System Zones 70, 88 89, 90, 91 Zone Definitions for Keypad Panic Zones 95, 96Zone Types Input TypesChoices for System Operation are Relay Outputs WorksheetsPage Ground Ademco VISTA-40 Summary of ConnectionsEileen Way, Syosset, New York
Top Page Image Contents