Honeywell 2-Partitioned Security System, VISTA-40 manual 2nd Page Programming Fields press *94

*80	*81	SYSTEM NON-ALARM CODES
		Enter 00-09; B-F (11-15).
		Default = 00 for all reports
		*80 1st Digit	*81 2nd Digit

1*30	RF RCVR CHECK-IN INTERVAL	[06]
	02-15 times 2 hours; 00 disables supervision
1*31	RF XMITTER CHECK-IN INTERVAL	[12]

Close

Open

Low Battery

Low Battery Restore

AC Loss

AC Restore

Test

Power Up

Cancel

Program Tamper

*83 FIRST TEST REPORT TIME

	02-15 times 2 hours; 00 disables transmitter supervision
1*33	TOUCHTONE W/ROTARY BACKUP		[0]
	1=enable; 0=disable
1*34	COMM. SPLIT REPORTING		[0]
		0=no; 1=alarms and alarm restores primary, others secondary;
		2=open/close, test secondary, others primary. See 751 for
		comments if using with dual reporting.
1*40		1*41 NON-ALARM DIALER CODES
		Enter 00-09; B-F (11-15).
		Default = 00 for all reports
		1*40 1st Digit	1*41 2nd Digit
		Armed STAY
		Time/Date Set or Event Log Reset
1*43	PERM. KEYPAD BACKLIGHT		[0]
	1=enable; 0=disable When disabled, display lights when any
	key is pressed, and turns off after period of keypad inactivity.
1*44	WIRELESS KEYPAD TAMPER		[0]

[Day 00; hour 12; min 00] Days 01-07 Hours 00-23 Min 00- 59; 00 in all boxes = instant (Day 01= Monday)

*84 SWINGER SUPPRESSION [03]

01-15 alarms

Must be "00" (disabled) for UL.

*85 ENABLE DIALER REPORTS FOR PANICS & DURESS

1=enable; [0=disable]

995 996 999 Duress

*87	ENTRY WARNING	[1]
	1=continuous; 0=3 beeps
*86	4208 MODULE ZONE ASSIGMENT	[0]

1 = allows 8 zones on one module (10-17), but prevents any other polling loop expansion. 0 = all other setups.

*88	BURG. ALARM COMM. DELAY			[0]
	1=16 seconds; 0=no delay
	Must be "0" for UL installations.
*89	RESTORE REPORT TIMING			[0]
	0=Instant; 1=At bell timeout if zone is restored; 2=when
	system is disarmed. Must be "0" for UL installations.
*90	SEC. SUBS. ACCT #
	Enter 00-09; B-F (11-15)		[15 15 15 15]
2nd Page Programming Fields (press *94)
1*01		1*09 ASSIGN RESPONSE TYPE FOR ZONES.
		Skip these fields. Use #93 Menu Mode, Zone
		Programming to program the response types.

MISCELLANEOUS WIRELESS OPTIONS

Fields 1*28 - 1*31 are not applicable for UL installations.

1*28	RF TX LOW BATTERY SOUND	[0]
	1=immediate; 0=when disarmed
1*29	RF TX LOW BATTERY REPORTING	[0]
	1=enable; 0=disable

	DETECTION
	1=enable; 0=disable.
	Must be "0" for UL installations.
1*45	EXIT DELAY SOUNDING	[0]
	1=enable; 0=disable. Produces quick beeping during exit
	delay if enabled.
	NOTE: See page 32, “SOUND OPTION”, prompt for
	disabling the entry/exit beeps on individual keypads.
1*46	AUXILIARY OUTPUT MODE	[0]

Enter 0 for ground start output. Enter 1 for open/close trigger. Enter 2 for keypad-like sounding. Enter 3 if AAV module is being used.

NOTE: Only one of the above options may be active within the system.

1*47	CHIME ON EXTERNAL SIREN	[0]
	1=enable; 0=disable
1*48	WIRELESS KEYPAD ASSIGNMENT	[0]
	0=disable; enter partition in which RF keypad used, 1-2.
	Must be "0" for UL installations.
1*49	SUPPRESS TX SUPERVISION SOUND	[1]
	1=disable; 0=enable.
	Must be "0" for UL installations.
1*52	SEND CANCEL IF ALARM + OFF	[0]
	1=no restriction; 0=within bell timeout period only
1*53	DOWNLOAD CALLBACK	[0]
	1=callback not required; 0=callback required.
1*57	5800 RF BUTTON GLOBAL ARM	[0]
	1=enable; 0=disable

– 7 –