First Alert FA148CPSSIA manual Menu Mode Output Function No, Activated By, Zone List, Zone Type

80 Menu Mode

					Output Function No.	Enter the output function number to be defined (or 00 to exit)
Output Funct. #
					(FA168CPS: 01-48
(00 = Quit)				01
					(FA148CP: 01-24)
					[∗] to continue; 00 to quit
					Summary Screen	This screen displays a summary of the current output
01	A	E	P	Trig
					[∗] to continue	programming (for this example, Zone List has been selected-this
?00	0	0	–	ZL=00
						is the default screen).
						A = Output Action; E = Triggering event; P = Partition;
						Trig = Trigger type
						NOTE: A question mark in the summary screen indicates that the
						device number shown has not been mapped. Use *79 Menu
						mode to map the device.
					Activated By	Select where the initiating event for this output definition is to
01 Activated By:
					0 = delete	occur as follows:
Zone List
					1 = zone list (go to “A”)	If you enter “0,” the following prompt appears:
					2 = zone type (go to “B”)	Delete?
					3 = zone number (go to “C”)
					[∗] to continue	0 = NO, 1 = YES

Press 1 to delete this output definition. The system deletes the output function and any previous programming.

A”

01 Zn List

1

Zone List

01-08 = zone list [∗] to continue

(prompt appears if zone list was selected)

Enter the desired zone list number associated with this output number. At the ENTER EVENT prompt, enter the zone list event that will activate this output

NOTE: Do not use pager zone lists 09-12 in output definitions.

Enter Event

Alarm 1

0 = restore; 1 = alarm;

2 = fault; 3= trouble

			NOTE: For alarm, fault, and trouble, an event on ANY zone in the
			list activates the output, but ALL zones in the list must be
			restored before the output is restored.
			Press [✱] to continue and skip to the “Output Action” prompt.
“B”		Zone Type	(prompt appears if zone type was selected)
		See list at right for available	Enter the desired zone type associated with this output number.
01 Enter Zn type
		zone types.	At the PARTITION prompt, enter the partition in which this zone
Perimeter	03
			type will occur.
			CHOICES FOR ZONE TYPES:
			00	= Not Used	05	= Day/Night		12	= Monitor Zone
			01	= Ent/Exit #1	06	= 24 Hr Silent		14	= Carbon Monoxide††
			02	= Ent/Exit #2	07	= 24 Hr Audible		16	= Fire w/verification
			03	= Perimeter	08	= 24 Hr Aux		23	= No Alarm Response
			04	= Interior Follower	09	= Fire		24	= Silent Burglary
					10	= Interior w/Delay		77	= Keyswitch Zone
								81	= AAV Monitor Zone
								90-91 = Configurable
			CHOICES FOR SYSTEM OPERATION:
			20	= Arming–Stay	36		= **At Bell Timeout***		58	= Duress
			21 = Arming–Away		38 = Chime				60	= AAV
			22	= Disarming	39		= Any Fire Alarm		61	= AVS/GSMV session begin§
			31	= End of Exit Time	40		= Bypassing		62	= AVS/GSMV session end §
			32	= Start of Entry Time	41		= **AC Power Failure		66	= Function Key†
			33	= Any Burglary Alarm	42		= **System Battery Low 67			= Bell Fail
					43		= Comm. Failure		68	= Telco Line Cut
					52		= Kissoff		78	= Keyswitch Red LED
					54		= Fire Zone Reset		79	= Keyswitch Green LED

**Use 0 (Any) for Partition No. (P) entry.

***Or at Disarming, whichever occurs earlier.

† Use *57 Menu Mode to assign the function key (function “07”).

††when used with an output function, the carbon monoxide zone type activates upon CO alarms only. Does not activate for trouble conditions. § automatically set when appropriate AVS Quick Command performed.

Note: In normal operation mode:

Code + # + 7 + NN Key Entry starts Device NN.

Code + # + 8 + NN Key Entry stops Device NN.

Enter the partition in which this zone type will occur.

01 Partition	0	= any partition; 1 = partition 1;
Any partition 0	2	= partition 2; 3 = common

Press [✱] to continue and skip to the “Output Action” prompt.

– 26 –