Type 00 Zone Not Used
Program a zone with this zone type if the zone is not used.
Type 01 Entry/Exit Burglary #1
•Assign to zones that are used for primary entry and exit.
•Provides entry delay when zone is faulted if control is armed in the Away, Stay, or Night-Stay modes.
•No entry delay provided when the panel is armed in the Instant/Maximum mode.
•Entry delay #1 is programmable for each partition (field *35).
•Exit delay begins whenever the control is armed, regardless of the arming mode selected, and is programmable (field ✱34).
Type 02 Entry/Exit Burglary #2
•Assign to zones that are used for entry and exit and require more time than the primary entry/exit point.
•Provides a secondary entry delay, similar to entry delay #1.
•Entry delay #2 is programmable for each partition (field *36).
•Exit delay is same as described for Type 01.
Type 03 Perimeter Burglary
•Assign to all sensors or contacts on exterior doors and windows.
•Provides an instant alarm if the zone is faulted when the panel is armed in the Away, Stay, Night-Stay, Instant or Maximum modes.
Type 04 Interior Follower
•Assign to a zone covering an area such as a foyer, lobby, or hallway through which one must pass upon entry (to and from the keypad).
•Provides a delayed alarm (using the programmed entry 1 time) if the entry/exit zone is faulted first. Otherwise this zone type gives an instant alarm.
•Active when the panel is armed in the Away mode.
•Bypassed automatically when the panel is armed in the Stay or Instant modes; if armed in Night-Stay mode, zones assigned to zone list 05 (night-stay zone list) are not bypassed when system armed in Night-Stay mode.
Type 05 Trouble by Day/Alarm by Night
•Assign to a zone that contains a foil-protected door or window (such as in a store), or to a zone covering a sensitive area such as a stock room, drug supply room, etc.
•Can also be used on a sensor or contact in an area where immediate notification of an entry is desired.
•Provides an instant alarm if faulted when armed in the Away, Stay, Night-Stay, Instant or Maximum (night) modes.
•During the disarmed state (day), the system will provide a latched trouble sounding from the keypad (and a central station report, if desired).
Type 06 24-hr Silent Alarm
•Usually assigned to a zone containing an emergency button.
•Sends a report to the central station but provides no keypad display or sounding.
Type 07 24-hour Audible Alarm
•Assign to a zone that has an emergency button.
•Sends a report to the central station, and provides an alarm sound at the keypad, and an audible external alarm.
Type 08 24-hour Auxiliary Alarm
•Assign to a zone containing an emergency button, or to a zone containing monitoring devices such as water or temperature sensors.
•Sends a report to the central station and provides an alarm sound at the keypad. (No bell output.)
Type 09 Supervised Fire
•Provides a fire alarm on short circuit and a trouble condition on open circuit. A fire alarm produces a pulsing bell output.
•This zone type is always active and cannot be bypassed.
Type 10 Interior w/Delay
•Provides entry delay (using the programmed entry time), if tripped when the panel is armed in the Away mode.
•Entry Delay 1 begins whenever sensors in this zone are violated, regardless of whether or not an entry/exit delay zone was tripped first.
•Bypassed when the panel is armed in the Stay or Instant modes; if armed in Night-Stay mode, zones assigned to zone list 05 (night-stay zone list) are not bypassed when system armed in Night-Stay mode.
Type 12 Monitor Zone
•Works as a dynamic monitor of a zone fault/trouble (not alarm). In the case of a short/open, the message, "*ALARM*-24 Hr. Non-Burg. -#XXX " (where XXX is the zone number) will be sent to the Central Station. The system keypad will display a “check” message indicating the appropriate zone (but keypad beeping does not occur). Upon restoral of the zone, the message, "*RESTORE*-24 Hr. Non-Burg. -#XXX " will be sent to the Central Station.
•The “check” message will automatically disappear from the keypad dynamically, when the zone restores; a user code + off sequence is not needed to reset the zone.
•Faults of this zone type are independent of the system, and can exist at the time of arming without interference.
•Since this is a “trouble” zone type, do not use this zone type with relays set to activate upon “alarm.”
Type 14 24 Hour Carbon Monoxide Monitor
•Assigned to any zone with a carbon monoxide detector.
•A carbon monoxide alarm produces keypad and detector sounding (does not affect bell output).
•Always active and cannot be bypassed.
Type 16 Fire w/Verification
•Provides a fire alarm when zone is shorted, but only after alarm verified.
•Verifies alarm by resetting smoke detectors after short is detected (removes power 7 seconds for zone 1, 3 seconds for trigger output). Another short circuit within 90 seconds triggers fire alarm.
•Provides a trouble response when zone is open.
Type 20 Arm-Stay (BR only)
•Arms the system in Stay mode when the zone is activated.
•Pushbutton units send the user number to the central station when arming or disarming.
•User number for button must be assigned.
Type 21 Arm-Away (BR only)
•Arms the system in Away mode when the zone is activated.
•Pushbutton units send the user number to the central station when arming or disarming.
•User number for button must be assigned.
Type 22 Disarm (BR only)
•Disarms the system when the zone is activated.
•User number for button must be assigned. Type 23 * No Alarm Response
•Can be used on a zone when an output relay action is desired, but with no accompanying alarm (e.g., lobby door access).
Type 24 Silent Burglary
•Usually assigned to all sensors or contacts on exterior doors and windows where bells and/or sirens are NOT desired.
•Provides an instant alarm, with NO audible indication at any keypad or external sounder, if the zone is faulted when the system is armed in the Away, Stay, Instant, or Maximum modes.
•A report is sent to the central station.
Type 77 Keyswitch
•Assign to zone wired to a keyswitch.
•Do not use input type “BR” devices with this zone type.
Type 81 AAV Monitor Zone
•Assign to zone connected to AAV module.
•Monitors 2-way voice sessions as follows:
-When the zone is faulted, all alarm sounding and dialer reporting stops, except for fire alarms, which immediately terminate the voice session and cause a fire report to be sent.
-When the zone is restored (session ended), sounding resumes (if bell timeout has not expired) and reports that were stopped are sent.
Types 90-93 Configurable
Allows for various custom responses. Options include response to entry/exit delays, response opens/shorts, types of alarm/trouble sounding, dial delay, and unique Contact ID report codes. Types 92 and 93 can only be programmed via downloader. UL installations: Zone Types 90 -93 may not be used as fire or burglar alarm zones on fire or UL burglar alarm installations.
*The system can still be armed when these zone types are in a faulted condition.
