First Alert FA148CPSSIA manual ∗31, ∗32, ∗33, ∗34, ∗35, ∗36, ∗37, ∗38

∗31	Single Alarm Sounding Per Zone
	0	= unlimited sounding
	1	= one alarm sounding per zone

SIA-Compliant Controls: If “0” selected, “alarm sounding per zone” will be the same as the “number of reports in armed period” set in field *93 (1 if one report, 2 if 2 reports, unlimited for zones in zone list 7).

[0]

If enabled, limits alarm sounding on the bell output to once per zone per armed period.

∗32	Fire Alarm Sounder Timeout
	0	= sound stops at timeout selected in
		field ∗33
	1	= no timeout; sounds until manually
		turned off

[0]

This control complies with NFPA requirements for temporal pulse sounding of fire notification appliances. Temporal pulse sounding for a fire alarm consists of the following: 3 pulses – pause – 3 pulses – pause – 3

pulses.

UL: must be 1 for fire installations

∗33	Alarm Sounder (Bell) Timeout
	0	= none	3 =12 min
	1	= 4 min	4 = 16 min
	2	= 8 min

[1]

This field determines whether the external sounder will shut off after time allotted, or continue until manually turned off.

UL: For residential fire alarm installation, must be set for a minimum of 4 min (option 1); for UL Commercial Burglary installations, must be minimum 16 min (option 4)

∗34	Exit Delay
	00	- 96 = 0 - 96 secs
	97	= 120 secs

SIA-Compliant Controls:

45 - 96 = 45 - 96 secs; 97 = 120 secs NOTE: Entries less than 45 will result in a 45-second delay.

		[60,60]
Part. 1	Part. 2

The system waits the time entered before arming entry/exit zones. If the entry/exit door is left open after this time expires, an alarm will occur. Common zones use same delay as partition 1.

SIA Guidelines: minimum exit delay is 45 seconds Common zones use part. 1 delay.

UL installations: For UL Commercial Burglar Alarm and UL Residential Burglar Alarm installations with line security, total exit time must not exceed 60 seconds.

∗35	Entry Delay #1
						[30,30]
	00 - 96 = 0 - 96 seconds		Part. 1		Part. 2
	97 = 120 secs
			Upon entering, the system must be disarmed before the time entered
	98 = 180 secs
			expires, otherwise it sounds an alarm.
	99 = 240 secs
			Common zones use same delay as part 1.
		SIA-Compliant Controls:	SIA Guidelines: minimum entry delay is 30 seconds
		30-96 = 30 - 96 secs; 97 = 120 secs;		For UL Residential Burglary Alarm installations, must be set for a maximum of
				30 seconds; entry delay plus dial delay should not exceed 1 min. For UL
		98 = 180 secs; 99 = 240 secs
				Commercial Burglar Alarm, total entry delay may not exceed 45 seconds.
		NOTE: Entries less than 30 will result
				Upon entering, the system must be disarmed before the time entered expires,
		in a 30-second delay.
				otherwise it sounds an alarm.
	Entry Delay #2
∗36
						[30,30]
	See *35 Entry Delay 1 for entries.
			Part. 1		Part. 2

∗37	Audible Exit Warning
	0 = no; 1 = yes
		SIA-Compliant Controls:	Feature
		always enabled; field does	not exist.

[1,1]

Part. 1 Part. 2

Warning sound consists of slow continuous beeps until the last 10 seconds, and then it changes to fast beeps. Sound ends when exit time expires.

SIA Guidelines: must be enabled

∗38	Confirmation Of Arming Ding
	0	= no
	1	= yes (wired keypads and RF)
	2	= yes, RF only (except 5827,
		5827BD)

[0,0]

Part. 1 Part. 2

Confirmation of arming is 1/2-sec external sounder “ding.”

If 1 selected, ding occurs when closing report is sent if open/close reporting is enabled, or at the end of Exit Delay. If 2 selected, ding occurs upon reception of the wireless arming command.

UL: must be 1 for UL Commercial Burglar Alarm inst.

– 5 –