Heat & Glo LifeStyle ESCAPE-I35-C owner manual Mantel and Wall Projections, Mantel Clearance

Page 20

B. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speciﬁed. Framing or ﬁnishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Clearance to combustible material under the insert is 1/4 inch (6 mm). Clearance from top of ﬁreplace opening for combustibles extending 12 inches max. is 12 inches.

•Use leveling legs to raise insert minimum 1/4 inch (6 mm) above combustible material or outer wrap of factory built ﬁrebox.

Combustible facings must not extend behind the insert surround. For non-combustible material speciﬁcations refer to section 1.E.

EXISTING NON-COMBUSTIBLE FACING

12 IN.

MAX.

12 IN. MIN.

Figure 5.3 Mantel Clearance

20	Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12

Image 20

Contents What to do if you smell gas Do not Discard this ManualCongratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Clear SpaceIPI Battery Tray/Battery Installation Control Module OperationBefore Lighting Fireplace Module Reset SwitchNine Hour Safety Shutdown Feature Lighting Instructions IPI Final inspection byFrequently Asked Questions After Appliance is LitMaintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote ControlMaintenance Tasks-Service Technician Gasket Seal and Glass Assembly InspectionVenting LogsBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Fireplace Size Requirements Minimum Fireplace OpeningMinimum Fireplace Size ESCAPE-I35-C ESCAPE-I30-C Mantel and Wall Projections Mantel ClearanceTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Venting Components Installing Vent Pipe and ApplianceVent Limits Connecting Vent Pipe Placing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap Factory BuiltGas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements IntelliFire PlusTM Ignition System WiringElectrical Information Code CSA C22.1Optional Accessories Installation for Fan OptionalProgramming the RC300 to the Control Module Orange to Valve Ground to Valve Bracket Green to ValveFinishing Appliance Setup Ember Placement Placement of Embers Escape-I30-CInstall the Log Assembly Log Set InstalledLOG #6 LOG Hangs Over Onto Burner TOPGlass Rock ESCAPE-I35-C, ESCAPE-I35LP-C LOG Contacts Left Grate Tine LOG Contacts Right Grate Tine LOG #4 Place LOG On Flat SpotAir Shutter Setting Air Shutter SettingsIntelliFire Plus Ignition System TroubleshootingSymptom Possible Cause Corrective Action Troubleshooting Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Log Set AssemblyAt Depot FireBrick InsertESCAPE-I35-C StockedService Parts ESCAPE-I30-C, ESCAPE-I35-C #15 Valve AssemblyESCAPE-I30-C Conversion Kits ESCAPE-I35-C Conversion KitsContact Information