Heat & Glo LifeStyle ESCAPE-I35-C owner manual Programming the RC300 to the Control Module

Page 30

Note: if any of the original wire as supplied with the appliance must be replaced, it must be replaced with type 105 °C rated wire.

BLOWERS

A UXI30 LI0 A RY

ORANGE - TO VALVE

GROUND - TO VALVE

BRACKET

GREEN - TO VALVE

PLUG INTO 120V

EXISTING OUTLET

I

P I

M	BRN
O	BRN
D
U
L
E

RED

BLK

INTO PLUGEXISTING OUTLET

MODULE IPI TO

WHT

GRN

BLK

FUSE WIRE

ASSEMBLY

FUSE WIRE

BLK ASSEMBLY

GRN

WHT

BLK

GRN

BLK

BLOWERS

BLK

GRN

BLK

Figure 10.3 Fan Wiring Diagram

NOTE: SEE FIGURE 10.1 FOR ADDITIONAL INFORMATION

G. Programming the RC300 to the Control Module

CAUTION! Risk of burns! DO NOT program the remote control to the control module when ﬁreplace is hot.

•Refer to the RC300 Installation Instructions included in appliance manual bag to program the RC300 to the control module.

30	Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12

Image 30

Contents What to do if you smell gas Do not Discard this ManualCongratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear SpaceIPI Battery Tray/Battery Installation Control Module OperationModule Reset Switch Nine Hour Safety Shutdown FeatureBefore Lighting Fireplace Lighting Instructions IPI Final inspection byFrequently Asked Questions After Appliance is LitGlass Cleaning Maintenance and ServiceMaintenance Tasks-Homeowner Remote ControlVenting Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection LogsBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Fireplace Size Requirements Minimum Fireplace OpeningMinimum Fireplace Size ESCAPE-I35-C ESCAPE-I30-C Mantel and Wall Projections Mantel ClearanceTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Installing Vent Pipe and Appliance Vent LimitsVenting Components Connecting Vent Pipe Placing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap Factory BuiltGas Pressure Gas InformationFuel Conversion Gas ConnectionElectrical Information Wiring RequirementsIntelliFire PlusTM Ignition System Wiring Code CSA C22.1Optional Accessories Installation for Fan OptionalProgramming the RC300 to the Control Module Orange to Valve Ground to Valve Bracket Green to ValveFinishing Appliance Setup Ember Placement Placement of Embers Escape-I30-CInstall the Log Assembly Log Set InstalledLOG #6 LOG Hangs Over Onto Burner TOPGlass Rock ESCAPE-I35-C, ESCAPE-I35LP-C LOG Contacts Left Grate Tine LOG Contacts Right Grate Tine LOG #4 Place LOG On Flat SpotAir Shutter Setting Air Shutter SettingsTroubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System Troubleshooting Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsAt Depot Service PartsLog Set Assembly FireBrick InsertESCAPE-I35-C StockedService Parts ESCAPE-I30-C, ESCAPE-I35-C #15 Valve AssemblyESCAPE-I30-C Conversion Kits ESCAPE-I35-C Conversion KitsContact Information