Heat & Glo LifeStyle ESCAPE-I35-C owner manual Reference Materials, Appliance Dimension Diagram

Page 43

14 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only.

K

A

H N R

P
Q	O
	O

S

B

E D

I

J					C
J					C

F

H

M

L

MODEL DIMENSIONS

	Escape-I35-C		ESCAPE-I30-C
Location	ESCAPE-I35LP-C		ESCAPE-I30LP-C
	Inches	Millimeters	Inches	Millimeters
A	25-1/4	641	21-1/4	552
B	34-3/4	864	30	762
C	31-1/2	800	26-3/4	679

D	20	508	18	457

E	24-5/8	626	22-9/16	573
F*	17	432	15-5/8	397
G	10-11/16	271	8-11/16	221

H	21-11/16	551	19-15/16	506

I	1-9/16	40	1-9/16	40
J	8-3/4	222	8-3/4	222

MODEL DIMENSIONS

	Escape-I35-C		ESCAPE-I30-C
Location	ESCAPE-I35LP-C		ESCAPE-I30LP-C
	Inches	Millimeters	Inches	Millimeters
K	7-13/16	183	6-3/8	162
L	1-7/16	37	1-7/16	37
M	8-1/2	216	7-1/8	181

N	3-11/16	94	3-11/16	94

O	6-3/8	162	6-3/16	157
P	1-13/16	46	1-15/16	49
Q	1-3/8	35	1-1/16	28

R	4-1/2	114	4-3/16	106

S	13-3/8	340	12-1/8	308

*Note: Location F on Figure 14.1 is measuring the appliance depth, for installation depth reference Location G on Figure 5.2.

Figure 14.1 Appliance Dimensions

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12

43

Image 43

Contents Do not Discard this Manual What to do if you smell gasHomeowner Reference Information CongratulationsUser Guide Table of ContentsLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optionalControl Module Operation IPI Battery Tray/Battery InstallationNine Hour Safety Shutdown Feature Module Reset SwitchBefore Lighting Fireplace Final inspection by Lighting Instructions IPIAfter Appliance is Lit Frequently Asked QuestionsRemote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection VentingIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Minimum Fireplace Opening Fireplace Size RequirementsMinimum Fireplace Size ESCAPE-I35-C ESCAPE-I30-C Mantel Clearance Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Vent Limits Installing Vent Pipe and ApplianceVenting Components Connecting Vent Pipe Placing, Securing and Leveling the Appliance Factory Built Installing Adaptor and Termination CapGas Connection Gas InformationFuel Conversion Gas PressureCode CSA C22.1 Wiring RequirementsIntelliFire PlusTM Ignition System Wiring Electrical InformationInstallation for Fan Optional Optional AccessoriesOrange to Valve Ground to Valve Bracket Green to Valve Programming the RC300 to the Control ModuleFinishing Appliance Setup Placement of Embers Escape-I30-C Ember PlacementLog Set Installed Install the Log AssemblyLOG Hangs Over Onto Burner TOP LOG #6Glass Rock ESCAPE-I35-C, ESCAPE-I35LP-C LOG Contacts Left Grate Tine LOG Contacts Right Grate Tine Place LOG On Flat Spot LOG #4Air Shutter Settings Air Shutter SettingSymptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System Troubleshooting Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsFireBrick Insert Service PartsLog Set Assembly At DepotStocked ESCAPE-I35-C#15 Valve Assembly Service Parts ESCAPE-I30-C, ESCAPE-I35-CESCAPE-I35-C Conversion Kits ESCAPE-I30-C Conversion KitsContact Information