Heat & Glo LifeStyle ESCAPE-I35-C owner manual LOG #4, Place LOG On Flat Spot

Page 39

PLACE LOG

ON FLAT SPOT

5	FLAT SPOTS
	FOR LOG #6
	CENTER
GROOVE MATES	BETWEEN
GROOVE MATES	LOG #3 AND
WITH GRATE BAR	LOG #4

Figure 8. Place Log #5

Log #5 (SRV2202-705):See Figures 2 and 3 for additional references. Place the thick end of Log #5 on the ﬂat spot of Log #1. Locate the groove on the thin end of the log. Mate the groove with the grate bar as shown above. Center the tip of Log #5 between the ends of Log #3 and Log #4.

PLACE LOG

ON FLAT SPOT

6

PLACE LOG

ON FLAT SPOT

Figure 9. Place Log #6

Log #6 (SRV2202-706):See Figures 2 and 8 for additional references. Place the thick end of the log on the ﬂat spot of Log #2. Place the thin end of Log #6 on the ﬂat spot of Log #5 as shown in Figure 9.

2202-935D

Heat & Glo • Escape-I35-C, Escape-I30-C • 2201-901 Rev. H • 5/12

39

Image 39

Contents Do not Discard this Manual What to do if you smell gasHomeowner Reference Information CongratulationsUser Guide Table of ContentsLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optionalControl Module Operation IPI Battery Tray/Battery InstallationModule Reset Switch Nine Hour Safety Shutdown FeatureBefore Lighting Fireplace Final inspection by Lighting Instructions IPIAfter Appliance is Lit Frequently Asked QuestionsRemote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection VentingIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Minimum Fireplace Opening Fireplace Size RequirementsMinimum Fireplace Size ESCAPE-I35-C ESCAPE-I30-C Mantel Clearance Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Installing Vent Pipe and Appliance Vent LimitsVenting Components Connecting Vent Pipe Placing, Securing and Leveling the Appliance Factory Built Installing Adaptor and Termination CapGas Connection Gas InformationFuel Conversion Gas PressureCode CSA C22.1 Wiring RequirementsIntelliFire PlusTM Ignition System Wiring Electrical InformationInstallation for Fan Optional Optional AccessoriesOrange to Valve Ground to Valve Bracket Green to Valve Programming the RC300 to the Control ModuleFinishing Appliance Setup Placement of Embers Escape-I30-C Ember PlacementLog Set Installed Install the Log AssemblyLOG Hangs Over Onto Burner TOP LOG #6Glass Rock ESCAPE-I35-C, ESCAPE-I35LP-C LOG Contacts Left Grate Tine LOG Contacts Right Grate Tine Place LOG On Flat Spot LOG #4Air Shutter Settings Air Shutter SettingTroubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System Troubleshooting Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsFireBrick Insert Service PartsLog Set Assembly At DepotStocked ESCAPE-I35-C#15 Valve Assembly Service Parts ESCAPE-I30-C, ESCAPE-I35-CESCAPE-I35-C Conversion Kits ESCAPE-I30-C Conversion KitsContact Information