Waterford Appliances E65-NG1 Optional Remote Control, Optional Wall Thermostat, Final Check

Page 28

INSTALLATION

2)Remove the glass panel by loosening the 6 screws securing the glass brackets. Sup- port the glass to prevent it from dropping out and breaking.

OPTIONAL REMOTE

CONTROL

5)Tighten the screws on the grill clips.

6)Replace the glass and secure the glass clips, reversing step 2)

7)Close the front door by reversing step 1).

Use the Waterford Remote Control Kit approved for this unit. Use of other systems may void your warranty.

The remote control kit comes with a hand held transmitter, a receiver and a wall mounting plate.

1)Choose a convenient location on the wall to install the receiver and the receptacle box (protection from extreme heat is very impor- tant). Run wires from the fireplace to that location, use Thermostat Wire Table.

2)Connect the wires as per the wiring dia- gram below.

3)Attach the 4 grill clips with the 4 screws but do not tighten down at this point.

4)Place the grill into position on the front of the door, center it in the front viewing area and use the grill clips to hold it in place.

OPTIONAL WALL

THERMOSTAT

A wall thermostat may be installed if desired. Connect the wires as per the wiring diagrams. Note that the wires are connected to the "TH" on the gas valve. Use table below to determine the maximum wire length:

Note: Preferable if the thermostat is in- stalled on an interior wall.

Waterford offers an optional programmable thermostat but any 250-750 millivolt rated non- anticipator type thermostat that is CSA, ULC or UL approved may be used.

CAUTION

Do not connect the millivolt

wall thermostat wires to the 120V wires.

Thermostat Wire Table

Recommended Maximum Lead Length

(Two-Wire) When Using Wall

Thermostat (CP-2 System)

Wire Size

Max. Length

 

14 GA.

50

Ft.

 

16 GA.

32

Ft.

 

18 GA.

20

Ft.

 

20 GA.

12

Ft.

 

22 GA.

9

Ft.

 

 

 

 

 

CAUTION

Do not connect the

millivolt remote control wires to the 120V wires.

3)Install 3 AAA alkaline batteries in transmitter and 4 AA alkaline batteries in the receiver. Install the receiver and its cover in the wall. Switch the remote receiver to "remote" mode. The remote control is now ready for operation.

FINAL CHECK

Before leaving this unit with the customer, the installer must ensure that the appliance is firing correctly. This includes:

1)Clocking the appliance to ensure the cor- rect firing rate (rate noted on label) at 15 minutes.

2)If required, adjusting the primary air to ensure that the flame does not carbon. First allow the unit to burn for 15 min. to stabilize.

3)Check for proper draft.

CAUTION

Any alteration to the product that causes sooting or carboning that results in dam- age to the exterior facia is not the respon- sibility of the manufacturer.

28

Waterford E65-1 Emerald Direct Vent Freestanding Gas Stove

Image 28
Contents Emerald Direct Vent Freestanding Gas Stove Models E65-NG1 Natural GasWaterford Unit SpecificationsTo the New Owner Table of Contents Safety Label Copy of Safety Label for E65-NG1 Natural Gas StoveCopy of Safety Label for E65-LP1 Propane Stove Installation SpecificationsSave These Instructions Information for MobileInstallation Checklist General Safety InformationClearances to Combustibles Manufactured Mobile Home Additional Requirements Locating Your Optional FAN Installation Emerald GAS StoveCombustion and Ventilation AIR Installation Introduction PrecautionsSafety Precautions for the Installer Ance adapterExterior Vent Terminal Locations Rigid Pipe Venting Components List 4DT-AJBHorizontal Venting Rigid Pipe Venting Horizontal TerminationsVenting Arrangements Examples Offset to Vertical Terminations Straight Vertical TerminationsVent Restrictor #1 Vertical Termination with CO-LINEAR Flex System Required PartsDescription Alternate Approved CapsMiniumum Horizontal Termination Installations Minimum components for a Horizontal Installa- tionDV Stove Horizontal Vent KIT Optional ComponentsInstallation Planning Your Dura-Vent Installation DURA-VENT Termination KITMinimum components for a Dura-Vent Horizontal Installation Alternate Horizontal Termination CapsMinimum components for a Dura-Vent Vertical Termination Dura-Vent Basic Horizontal Kit #Below Grade Snorkel Installation DURA-VENT Horizontal InstallationsSnorkel Terminations DURA-VENT Vertical Termination # 942 over the vent pipeCathedral Ceilings Offset ChartRound Support RDS Square Support SQS Prior to installation and connection Support Extensions Round Rdse or Square SqseGeneral Converting a Factory Built Metal ChimneyConverting a Masonry Chimney Aeration Adjustment High ElevationGAS Connection With 38,000 BTUConversion KIT from Natural GAS to Propane GAS Pipe Pressure TestingValve Description Natural Gas Conversion Kit 260-920 Contains Reduction KIT to Lower BTU Rating for E65-1 GAS StovePropane Conversion Kit 260-922 Contains Optional Door Grill Installation LOG InstallationDoor Grill Kit Contains Optional Wall Thermostat Optional Remote ControlFinal Check Wiring Diagram E65-NG1 & E65-LP1 Lighting ProcedureOperating Instructions Operating InstructionsFirst Fire Shutdown ProcedureCopy of the Lighting Plate instructions Maintenance Adjusting Flame HeightMaintenance Instructions Automatic Convection FAN OperationGeneral Vent Maintenance LOG ReplacementGlass Replacement FAN MaintenanceInstalling Valve Assembly To remove valve from valve assembly, continueRemoving Valve To remove fanParts List Main AssemblyBurner & LOG Assembly Waterford E65-1 Emerald Direct Vent Freestanding Gas Stove Waterford E65-1 Emerald Direct Vent Freestanding Gas Stove Page Warranty ConditionsRegister your Waterford online at