Regency L676S-NG1 installation manual Mantel Clearances, Mantel LEG Clearances

Page 10

INSTALLATION

INSTALLATION

MANTEL CLEARANCES

Because of the extreme heat this ﬁreplace emits, the mantel clearances are critical. Combustible mantel clearances from top of front facing are shown in the diagram below.

Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board.

Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour.

MANTEL LEG CLEARANCES

Combustible mantel leg clearances as per diagram:

MANTEL LEG

L676S UNIT

4" 1.5"

Allowable mantel	9” (229mm)
Allowable mantel
leg projection
	11” (279mm)
Side wall	14-3/4” (375mm)
	14-3/4” (375mm)

10	Regency® L676S Direct Vent Gas Fireplace

Image 10

Contents L676 Sunrise Gas Fireplace Manufactured Mobile Home Requirements Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Serial No. / No de serie Safety LabelCopy of Safety Decal Factory Equipped For Altitude 0-4500ft -1372mRequirements For the State of Massachusetts onlyUnit Dimensions Installation Checklist InstallationGeneral Safety Information Important Message Save These InstructionsFinished Floor Manufactured Mobile Home Additional RequirementsHeat Release KIT Locating Your GAS FireplaceClearances Mantel Clearances Mantel LEG ClearancesImportant Header must be metal stud. All other framing may Installed. See Diagram 3 for detailsFraming FramingNon-combustible FinishingMaterial + 3/8 + 3/4Finishing Template Unit Assembly Prior to InstallationVenting Introduction Vent Restrictor Plate Latch No adjustment requiredVent Restrictor Position Latch Location HingeDoorMinimum Clearance Requirements Exterior Vent Termination RequirementsCanada1 Venting Arrangements Horizontal Termination FlexRigid Pipe Venting Systems Basic Horizontal & Vertical Terminations8 Rigid Pipe Cross Reference Chart Installation Vent Restrictor On Set Allowable Horizontal TerminationsVertical Vent Restrictor On Set Option + H1 Option + V1 H + H1Option + H1 V + V1 With these options, max. totalAllowable Vertical Terminations Unit Installation with Horizontal Termination Diagram Unit Installation With Vertical TerminationThis allows for small adjustments Minimum VentUnit Installation Astrocap XLGAS Pipe Pressure Testing Pilot AdjustmentGAS Line Installation High ElevationMinimum Air Shutter Opening Aeration AdjustmentWiring Diagram OptionalConversion KIT #526-969 from NG to LP LP Conversion Kit Contains Qty DescriptionLeaks Firebox base Panel InstallationStainless Steel Panels Black Enamel Panels Slots on ﬂ oor of ﬁ rebox baseLeft panel Holes on bottom PanelUse this hole on panel clip Spread the supplied Glass Crystals or optional Ceramic Spa Level adjustment Faceplate & Door Frame InstallationAdjustment for ﬁ nishing materials Location of mounting bracketsOperating Instructions Copy of Lighting Plate Instructions For Your Safety Read Before LightingNormal Operating Sounds GAS Appliances Lighting InstructionsMaintenance DC Spark Box Wires DC Spark BOX Battery ReplacementDC Spark BOX Replacement DC Spark Box LocationDoor Hinge with door removed Valve Tray ReplacementSlots for back panel Location of Screws Disconnect 2 generator wires Disconnect 2 wiresDC Spark Box Electrode Wire Valve Tray OutParts List Main AssemblyHeat Wave Kit Release Kit Burner Assembly Regency L676S Direct Vent Gas Fireplace Regency L676S Direct Vent Gas Fireplace Warranty ConditionsInstaller Please complete the following information