Regency L676S-NG1 Panel Installation, Stainless Steel Panels Black Enamel Panels, Firebox base

Page 32

INSTALLATION

INSTALLATION

PANEL INSTALLATION

Important: One set of panels must be installed. Operation of this unit without panels is prohibited.

Before installation, panels must be handled and cleaned as per instructions noted below:

Stainless Steel Panels

Black Enamel Panels

• Stainless panels must be inspected for scratches and dimples prior

• Black Enamel panels must be inspected for scratches and dimples

to installation. All claims to be recorded at this time.

prior to installation. All claims to be recorded at this time.

Claims for damage after installation will not receive consideration.

Claims for damage after installation will not receive consideration.

To protect the finish during installation and handling - cotton gloves MUST be worn at all times while handling the panels (even when removing protective coating).

• Stainless panels will discolor a little during normal operation.

• Black Enamel panels will discolor a little during normal operation. This

This is normal and should not be considered a defect.

is normal and should not be considered a defect.

 

 

 

All hand and finger marks MUST be cleaned off with a soft cloth and

 

All hand and finger marks MUST be cleaned off with a soft cloth. Use

*a stainless steel cleaner. Most stainless steel cleaners leave a film/

an ammonia based cleaner (ie. glass cleaner) to remove any fingerprints

*

 

residue on the surface of the panels. Use an ammonia based cleaner

before applying heat to the unit.

(ie. glass cleaner) to remove this film before applying heat to the unit.

Failure to do this will result in burn stain on panels which you

Failure to do this will result in burn stains on panels which you

will be unable to remove. Not protected by product warranty.

will be unable to remove. Not protected by product warranty.

 

 

1)With firebox base in position, install back panel first by fitting the tabs on the back panel in to slots in firebox base.

Firebox base.

Back panel.

Slots on fl oor of fi rebox base.

32

Regency® L676S Direct Vent Gas Fireplace

Image 32
Contents L676 Sunrise Gas Fireplace Manufactured Mobile Home Requirements Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label Copy of Safety DecalSerial No. / No de serie Factory Equipped For Altitude 0-4500ft -1372mRequirements For the State of Massachusetts onlyUnit Dimensions Installation General Safety InformationInstallation Checklist Important Message Save These InstructionsManufactured Mobile Home Additional Requirements Heat Release KITFinished Floor Locating Your GAS FireplaceClearances Mantel Clearances Mantel LEG ClearancesInstalled. See Diagram 3 for details FramingImportant Header must be metal stud. All other framing may FramingMaterial FinishingNon-combustible + 3/8 + 3/4Venting Introduction Unit Assembly Prior to InstallationFinishing Template No adjustment required Vent Restrictor PositionVent Restrictor Plate Latch Latch Location HingeDoorCanada1 Exterior Vent Termination RequirementsMinimum Clearance Requirements Venting Arrangements Horizontal Termination FlexRigid Pipe Venting Systems Basic Horizontal & Vertical Terminations8 Rigid Pipe Cross Reference Chart Installation Vertical Vent Restrictor On Set Allowable Horizontal TerminationsVent Restrictor On Set Option + H1 Option + V1 H + H1Option + H1 V + V1 With these options, max. totalAllowable Vertical Terminations Unit Installation with Horizontal Termination Unit Installation With Vertical Termination This allows for small adjustmentsDiagram Minimum VentUnit Installation Astrocap XLPilot Adjustment GAS Line InstallationGAS Pipe Pressure Testing High ElevationAeration Adjustment Wiring DiagramMinimum Air Shutter Opening OptionalConversion KIT #526-969 from NG to LP LP Conversion Kit Contains Qty DescriptionLeaks Panel Installation Stainless Steel Panels Black Enamel PanelsFirebox base Slots on fl oor of fi rebox baseUse this hole on panel clip Holes on bottom PanelLeft panel Spread the supplied Glass Crystals or optional Ceramic Spa Faceplate & Door Frame Installation Adjustment for fi nishing materialsLevel adjustment Location of mounting bracketsOperating Instructions For Your Safety Read Before Lighting Normal Operating Sounds GAS AppliancesCopy of Lighting Plate Instructions Lighting InstructionsMaintenance DC Spark BOX Battery Replacement DC Spark BOX ReplacementDC Spark Box Wires DC Spark Box LocationSlots for back panel Valve Tray ReplacementDoor Hinge with door removed Disconnect 2 wires DC Spark Box Electrode WireLocation of Screws Disconnect 2 generator wires Valve Tray OutParts List Main AssemblyHeat Wave Kit Release Kit Burner Assembly Regency L676S Direct Vent Gas Fireplace Regency L676S Direct Vent Gas Fireplace Warranty ConditionsInstaller Please complete the following information