Wayne T75S10-4, T75S10-2, T50S10-4, T50S10-2, T100S10-2, T51S10-4 warranty Control box chart

Operating Instructions and Parts Manual							Deep Well Submersible Pump
						Cable Size
		14	12	10	8	6	4	3	2	1	0
Volts	HP	(2 mm2)	(3 mm2)	(5 mm2)	(7 mm2)	(13 mm2)	(21 mm2)	(25 mm2)	(34 mm2)	(41 mm2)	(50 mm2)
	1/2	400	650	1020	1610	2510	3880	4810	5880	7170	8720
		(121.9)	(198.1)	(310.9)	(490.7)	(765)	(1182.6)	(1466.1)	(1792.2)	(2185.4)	(2657.9)
230	3/4	300	480	760	1200	1870	2890	3580	4370	5330	6470
		(91.4)	(146.3)	(231.6)	(365.8)	(570)	(880.9)	(1091.2)	(1332)	(1624.6)	(1972.1)
	1	250	400	630	990	1540	2380	2960	3610	4410	5360
		(76.2)	(121.9)	(192)	(301.8)	(469.4)	(725.4)	(902.2)	(1100.3)	(1344.2)	(1633.7)

NOTE: Specified maximum wire lengths are valid with motor voltage greater than or equal to 95% of service entrance voltage and motor running at maximum nameplate amperes. If service entrance voltage is at least motor nameplate voltage under normal load conditions, 50% additional length is permissible for all sizes shown.

Table 3 - Power supply wire (cable) length in feet (m)

1 phase, 2 or 3 wire cable, 60 Hz (copper wire size—service to motor)

Electrical System

(Continued)

use only control box specified

for your pump. Make sure motor and control box match (see Table 4, on page 3). Failure to do so will void warranty.

4.Install circuit protection and component protection in compliance National Electrical Code, Part 1. Consult with appropriate code officials for more information on how to do this.

			Pump Model	Control Box
HP	Voltage	Wires	No.	No.
1/2	230	3	T50S10-2	16965-002
1/2	230	2	T50S10-2	None
1/2	115	2	T51S10-4	None
3/4	230	3	T75S10-2	16966-002
3/4	230	2	T75S10-4	None
1	230	3	T100S10-2	16967-002

Table 4 - Control box chart

If main overload trips, look for the
following:	115V or	GROUND				TO LINE	GROUND
1. Shorted capacitor	230V LINE
		FUSED
2. Voltage problems
		DISCONNECT
3. Overloaded or locked pump.		SWITCH			CONTROL
					BOX
Single Phase, 2 Wire		L1	M1		L1L2R Y B		L1	M1
Two-wire pumps have two power supply
		L2 M2					L2	M2
wires and one ground wire (Green). A
				PRESSURE
control box is not required. See Figure						FUSED
1b for correct hookup for 230 volt		RED		SWITCH		DISCONNECT
						SWITCH		PRESSURE
2-wire motors only.		YELLOW
								SWITCH
		BLACK
							RED
							BLACK
			WELL		GROUND
									GROUND
			CASING
								WELL	(GREEN)
		Follow color coding when						CASING
		connecting control box wires.
		(Yellow = Y, Red = R, Black = B)
	Figure 1a - 3 wire, 1/2-1HP quick					Figure 1b - Single phase, 2 wire
	disconnect box					connections
								www.waynepumps.com
			3