Wayne-Dalton 3324B-Z Alignment of Wired Infrared, Safety Sensors, Be Closed by Continuously

Page 18

16

 

Alignment of Wired Infrared

 

 

 

 

 

Safety Sensors

 

 

 

 

 

Tools Needed:

 

 

 

 

 

 

WARNING

 

 

 

 

 

Pliers

 

TO AVOID POSSIBLE SEVERE OR FATAL

 

 

INJURY, KEEP PEOPLE AND OBJECTS

 

 

CLEAR OF THE MOVING DOOR ARM TO

 

 

PREVENT POSSIBLE PERSONAL INJURY.

IMPORTANT: THE SAFETY SENSOR SENDS

AN INVISIBLE BEAM OF LIGHT FROM THE

SENDING UNIT TO THE RECEIVING UNIT

ACROSS THE PATHWAY OF THE DOOR. THE

OPENER WILL NOT OPERATE UNTIL THE

SAFETY SENSORS ARE CONNECTED TO THE

OPENER AND PROPERLY ALIGNED. IF THE

INVISIBLE BEAM OF LIGHT IS OBSTRUCTED,

AN OPEN DOOR CANNOT BE CLOSED BY

THE TRANSMITTER OR A MOMENTARY

ACTIVATION OF THE WALL STATION UP/

DOWN BUTTON. HOWEVER, THE DOOR MAY

BE CLOSED BY CONTINUOUSLY

HOLDING YOUR FINGER ON THE WALL

STATION UP/DOWN BUTTON (CONSTANT

PRESSURE) UNTIL THE DOOR TRAVELS TO A

FULLY CLOSED POSITION.

At this point you will be able to activate the opener. The trolley/ upper arm will move to the open position, but will not move to the closed position unless the beams are aligned.

The safety sensors must be aligned by moving the sending and receiving units in or out until the alignment light on the receiving unit comes on. The 1/4”-20 carriage bolt can be loosened to move the unit in or out, as required. If you have difficulty

aligning beams, check that both brackets are mounted at the same height (see Step 11) and remount if necessary. Additional minor adjustments can be made by lightly bending the mounting brackets.

Once the alignment light comes on, tighten all bolts and mounting screws.

Finish securing all wiring making sure not to break or open any of the conductors. Loop and secure any extra wire.

Using the wall station up/down button, activate the opener and check that it will operate through full open and close. Ensure trolley and trolley latch are in the closed position prior to proceeding to next step.

In

 

 

In

Out

 

 

Out

1/4”-20 Carriage Bolts

For this adjustment, bend mounting brackets

at wall mount

 

Top View

Up/Down

 

 

 

Button

 

 

 

Wired Wall station

 

 

ra

te

 

e

 

p

 

D

o

O

 

o

 

o

 

 

r

T

Press

 

 

Here

Up/Down

 

 

 

Button

 

 

 

Multi-Function Wall Station

RF Transmitter

12Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Important Notice Garage Doors & OpenersNew 9/18/2008 Package Contents Page Door Test One Pre-InstallationDisconnect from power source and proceed to assembly Door Test TwoSystem Features Tools NeededHomelink Compatibility Rolling Code Technology Table of Contents Definition of key words used in this manualInstallation Attaching Opener to RailPositioning and Installing Front Wall Bracket Service PersonReinforce the Header Wall Attach Unit to Front Wall Bracket Positioning MotorEnd of Opener AT Least 3 Feet LongProper Installation Mounting Opener EndManufacturer for Proper Installing LightMounting Door Bracket Reinforcing of Your DoorWall Station Near or Next to Wired Wall Station Installation If IncludedDoor can be Seen When Garage DoorWall Station OUT of the Reach Wall Station Installation If IncludedWall Station Near or Next to Garage Door Children and in a Location WhereNot adhere EntrapmentApply entrapment warning label in a Convenient location next to the wall stationNut Wired Infrared Safety Sensor InstallationWall Mounting Bracket Door Jam WasherConnecting Wired Infrared Safety Installation of Wiring for WiredInfrared Safety Sensor Sensor to OpenerTo Latch Assembly Connecting OpenerConnecting Trolley Cord in AnywayBe Closed by Continuously Alignment of Wired InfraredSafety Sensors Fully Closed PositionSetting Trolley Close Position ARMTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Close Travel Setting Door Opening TravelStop Bolt Trolley Opener Contact Obstruction Test Fatal Injury MAY ResultPossible Personal Injury Programming Wireless KeylessEntry If Included To Prevent Door Damage orSurface inside garage Important Install ALL WallWood framing using the two screws MaterialsImportant Check Your Local Power ConnectionTo Avoid Electrical Shock Instructions IllustratedMounting Door Bracket To Series Door Optional InstallationsTools Needed Power Drill Socket Driver 14 x 5/8 self tapping screws as shown in FIGBAR Must be Adjusted ProperlyImportant When Connecting a Shown in FIGFor Portland Track Radius Being UsedTrack LOW HeadroomConnecting Door Arm DIM Type of ARMDetermine the WAYNE-DALTON Track Radius Being Used LOW Headroom Trolley LOW Headroom Trolley Positioning Chart forOptional Hookup 15-18Read and Follow ALL Instructions HOW the Light Works and What IT Means When IT FlashesOperation Door activationOperating the Wireless Wall Station Customizing the Settings Opener ControlsUp/Down Button Primary Programming for HomeLink to the Prodrive Programming/Training HomeLink UnitTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Closing Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Opening Force AdjustmentWall Station Tools Needed NoneTransmitter Large ButtonMaintenance Battery Replacement for Wall StationTwice a Year  Troubleshooting MAINTENANCE/ TroubleshootingSymptom Probable Cause Corrective Action Parts Breakdown Rail Assembly All Models Description # Per UnitParts Breakdown Opener Assembly And Accessories All Models 2524Prodrive Accessories Wireless Keyless Entry80ft gauge, 2 conductor polarized. UL listed CL-2, 75deg. C Pre-drill 5/64 pilot hole Pre-drill 3/32 pilot holeDrill Template Multifunction ButtonPlease Do Not Return This Product To The Store Thank you for your purchaseLifetime Limited Warranty Replacement laborPatent Information FCC and IC Statement¡AVISO Importante Pieza nroContenido del paquete Page Prueba dos de la puerta Antes de la instalaciónPrueba uno de la puerta Costado derecho del accionadorCaracterísticas del sistema Herramientas necesariasTabla de materias Leer Y Seguir Todas LAS Instrucciones DE InstalaciónMontaje del accionador en el riel InstalaciónTransmisión Puerta Del garajeFrontal Travesaño y cerrar la puertaFijar la unidad en el soporte De pared frontal Posicionamiento del extremo Motor del accionadorMontaje del extremo Del accionadorInstalación de iluminación Montaje de soporte de puertaOperación Apropiado Para LA PuertaCausar EL Malfuncionamiento DEL Accionador LA Estación DE Pared Fuera DELDE Garaje Apropiado CON EL InterruptorLA Puerta DE Garaje Sobre aprisionamiento Instalación de la estaciónEtiqueta de advertencia Adhesivo no funcionaHerramientas necesarias De seguridad, cableadoInstalación de sensor infrarrojo ArandelaInstalación de cableado Conexión del sensor infrarrojo deSeguridad cableado al accionador Conexión del trole al Conexión del accionadorAl tomacorriente Conjunto del pestilloDesplace Hasta LA Posición Alineación de los sensoresLesiones Personales Completamente CerradaConfiguración de la posición Cerrada del troleMóvil DE LA Puerta Modelos 9700 y Conexión de brazoPara puerta a puerta 10 aCalibración del recorrido Calibración de recorridoDe cierre de la puerta De apertura de la puertaPerno de tope Trole Accionador Prueba de obstrucción Del sensor de seguridad Prueba de obstrucciónPor contacto Causar Lesiones Graves O FatalesHerramientas Programación del accesoInalámbrico sin llave Posibles Lesiones PersonalesGaraje Instalación del accesoUbicación de cada tornillo En otros materialesConexión eléctrica opción de Cableado permanente IlustradasTaladro eléctrico Vástago de cubo De 7/16˝ Montaje de soporte de puerta Una puerta SerieInstalaciones Opcionales Para LA Sección Superior CON Barra UMordazas de Montaje del soporte de puerta a unaContinuar con el Paso PresiónDe cierre del trole / Conexión Del brazo de la puertaFranqueo Superior Reducido Conexión OpcionalEl trole y reinstalar la chaveta hendida Configuración de la posición deCierre del trole / Conexión del En la páginaDel accionador CON Franqueo Superior ReducidoParte inferior Riel con franqueo Superior reducido Brazo curvoActivación de la puerta Leer Y Seguir Todas LAS InstruccionesJamás Ubicarse Bajo UNA Puerta PARADA, Parcialmente Abierta Cómo Funciona LA LUZ Y QUÉ Significa Cuando DestellaOperación de la estación inalámbrica de pared Posición personalizada para mascotas Personalización de la configuraciónControles del accionador Comenzar con la puerta en la posición cerradaProgramación primaria de HomeLink para Prodrive Programación alternativa de HomeLink para Prodrive Ajustes Ajuste DE LA Fuerza DE CierreAjuste DE LA Fuerza DE Apertura Transmisor TransmisorEstación DE Pared Mantenimiento Dos veces al añoCambio de pilas para la estación de pared  Diagnóstico y resolución de problemas Mantenimiento / Diagnóstico Y Resolución DE ProblemasSíntoma Causa Probable Acción Correctiva Nro. por unidad Pieza Nro. porNro Descripción Unidad 309960 Conjunto de pestillo para cadena 18b 325687Cordón de suministro eléctrico Transitorias MOV 252993 Interruptor de límites 311365Juego de sensor infrarrojo de seguridad Acceso inalámbrico sin llave de 5 botonesPara instalación en pared Accesorios del ProdriveDe operación a radiofrecuencia Acceso inalámbricoPlantilla recortable para ayudar en la instalación Pre-drill 5/64 pilot holePlantilla DE Perforación Pre-drill 3/32 pilot holeCualquier pregunta y/o enviarán cualquier pieza necesaria Gracias por su compraGarantía Limitada DE POR Vida Información sobre patentes Declaración de la FCC e ICInformación normativa de la FCC

3324B-Z specifications

Wayne-Dalton is renowned for its commitment to innovative door solutions, and the Wayne-Dalton 3324B-Z is a prime example of their cutting-edge offerings in the realm of garage doors. This model is designed for residential settings, combining aesthetics with functionality.

One of the standout features of the 3324B-Z is its construction. The door is made from high-quality steel, ensuring exceptional durability and resistance to external elements. This steel is reinforced to provide strength and support, which is critical for maintaining the stability of the door over time. Moreover, the door is insulated with polyurethane, offering enhanced thermal efficiency. This insulation not only helps to regulate temperature within the garage but also contributes to energy savings by reducing heating and cooling costs.

Aesthetic appeal is another hallmark of the Wayne-Dalton 3324B-Z. Featuring a contemporary design, it is available in multiple color options and finishes, allowing homeowners to customize the look of their home while enhancing curb appeal. The door's design includes raised panel sections that add depth and texture, making it visually appealing without compromising on functionality.

In terms of technology, the Wayne-Dalton 3324B-Z integrates various advancements to enhance user experience and safety. It is equipped with a reliable spring system that promotes smooth operation and extends the lifespan of the door. The door can also be paired with Wayne-Dalton's innovative Quantum garage door opener, which features advanced security and remote access capabilities, allowing homeowners to operate their doors from anywhere via a smartphone app.

Safety is a paramount consideration in the design of the 3324B-Z. The door incorporates features such as pinch-resistant design, reinforced hinges, and safety sensors to protect users and pets from potential accidents during operation.

Installation and maintenance are also simplified with the Wayne-Dalton 3324B-Z. The door comes with detailed instructions for easy setup, and its durable materials require minimal upkeep, ensuring a long-lasting performance with minimal hassle.

In conclusion, the Wayne-Dalton 3324B-Z is a sophisticated choice for any homeowner seeking a balance of style, durability, and advanced technology. Its robust construction, attractive design, and safety features make it an ideal addition to modern homes. Whether upgrading an existing garage door or installing a new one, the 3324B-Z is a solution that stands out in functionality and aesthetics.
Top Page Image Contents