Wayne-Dalton 3324B-Z installation instructions Contact Obstruction Test, Fatal Injury MAY Result

Page 23

21

Contact Obstruction Test

 

 

 

Tools Needed:

After installing the opener, the door must

 

 

reverse when it contacts a 1 1/2” inch high

 

2 x 4 Board

object (or a 2 x 4 board laid flat) on the

 

 

garage floor.

 

 

Using the wall station, activate the door to

 

 

the fully open position. Place a 2 x 4 flat

 

 

on the garage floor, under the door path.

 

 

Activate the door to the closed position with

 

 

the wall station. Upon contacting the 2 x 4

 

 

board, the door should reverse.

 

 

If door stops on the 2 x 4 board, adjust

2 x 4 Laid Flat

 

On The Floor

 

the close travel knob 1/8-1/4 turn “more”

 

 

until door reverses upon contact with 2 x 4

 

 

board.

 

 

When the door reverses, remove the

 

 

2 x 4 board and run the full cycle of open

 

 

and close of the door. Door should not

WARNING

 

reverse when it comes to the fully closed

 

 

 

position on the floor.

IF OPENER DOES NOT RESPOND PROPERLY TO THESE TESTS (STEPS

 

 

 

NOTE: If opener fails to pass this test,

21 AND 22), HAVE A QUALIFIED SERVICE PERSON MAKE NECESSARY

 

ADJUSTMENTS/REPAIRS, OR SEVERE OR FATAL INJURY COULD

 

repeat Step 19. Also see Adjustment #2,

 

RESULT FROM OPERATING THE DOOR/OPENER.

 

page 32 (Contact Obstruction Test).

 

 

22

 

Safety Sensor Obstruction Test

Tools Needed:

 

 

 

 

 

 

WARNING

 

 

 

 

 

2” x 6” x 12”

WHEN PERFORMING THIS PART OF THE

Solid Test Object

TEST, DO NOT PLACE YOURSELF UNDER

 

DESCENDING DOOR, OR SEVERE OR

 

FATAL INJURY MAY RESULT.

 

Starting with the door fully open, place a 6”

 

high object on the floor, in line with sensors,

 

12” from the left side of the door.

 

Activation of the opener with the wall station

 

Up/Down button should cause the door to

 

move no more than one foot, stop and then

 

reverse to fully open position.

 

Repeat this test with the 6” high object

 

placed at the center of the door and then

 

12” from the right side of the door.

 

The 6” high object, when placed on the floor

 

in line with sensors, while door is closing,

 

should also cause the door to reverse.

 

Sensor

6”

12”

 

12”

 

Sensor

 

WARNING

IF OPENER DOES NOT RESPOND PROPERLY TO THESE TESTS (STEPS 21 AND 22), HAVE A QUALIFIED SERVICE PERSON MAKE NECESSARY ADJUSTMENTS/REPAIRS, OR SEVERE OR FATAL INJURY COULD RESULT FROM OPERATING THE DOOR/OPENER.

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 17 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 22 Page 24
Image 23
Page 22 Page 24
Contents New 9/18/2008 Important NoticeGarage Doors & Openers Package Contents Page Door Test Two Pre-InstallationDisconnect from power source and proceed to assembly Door Test OneHomelink Compatibility Rolling Code Technology System FeaturesTools Needed Definition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationReinforce the Header Wall Positioning and Installing Front Wall BracketService Person AT Least 3 Feet Long Positioning MotorEnd of Opener Attach Unit to Front Wall BracketMounting Opener End Proper InstallationReinforcing of Your Door Installing LightMounting Door Bracket Manufacturer for ProperGarage Door Wired Wall Station Installation If IncludedDoor can be Seen When Wall Station Near or Next toChildren and in a Location Where Wall Station Installation If IncludedWall Station Near or Next to Garage Door Wall Station OUT of the ReachConvenient location next to the wall station EntrapmentApply entrapment warning label in a Not adhereWasher Wired Infrared Safety Sensor InstallationWall Mounting Bracket Door Jam NutSensor to Opener Installation of Wiring for WiredInfrared Safety Sensor Connecting Wired Infrared SafetyCord in Anyway Connecting OpenerConnecting Trolley To Latch AssemblyFully Closed Position Alignment of Wired InfraredSafety Sensors Be Closed by ContinuouslyTo Avoid Possible Injury or Setting Trolley Close PositionARM Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Fatal Injury MAY Result Contact Obstruction TestTo Prevent Door Damage or Programming Wireless KeylessEntry If Included Possible Personal InjuryMaterials Important Install ALL WallWood framing using the two screws Surface inside garageInstructions Illustrated Power ConnectionTo Avoid Electrical Shock Important Check Your Local14 x 5/8 self tapping screws as shown in FIG Optional InstallationsTools Needed Power Drill Socket Driver Mounting Door Bracket To Series DoorShown in FIG Must be Adjusted ProperlyImportant When Connecting a BARLOW Headroom Radius Being UsedTrack For Portland TrackDIM Type of ARM Connecting Door ArmDetermine the WAYNE-DALTON Track Radius Being Used 15-18 LOW Headroom Trolley Positioning Chart forOptional Hookup LOW Headroom TrolleyDoor activation HOW the Light Works and What IT Means When IT FlashesOperation Read and Follow ALL InstructionsOperating the Wireless Wall Station Up/Down Button Customizing the SettingsOpener Controls Teaching HomeLink to the opener Primary Programming for HomeLink to the ProdriveProgramming/Training HomeLink Unit Alternate Programming for HomeLink to the Prodrive Opening Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Closing Force AdjustmentLarge Button Tools Needed NoneTransmitter Wall StationTwice a Year MaintenanceBattery Replacement for Wall Station Symptom Probable Cause Corrective Action  TroubleshootingMAINTENANCE/ Troubleshooting Description # Per Unit Parts Breakdown Rail Assembly All Models2524 Parts Breakdown Opener Assembly And Accessories All Models80ft gauge, 2 conductor polarized. UL listed CL-2, 75deg. C Prodrive AccessoriesWireless Keyless Entry Multifunction Button Pre-drill 3/32 pilot holeDrill Template Pre-drill 5/64 pilot holeThank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent InformationPieza nro ¡AVISO ImportanteContenido del paquete Page Costado derecho del accionador Antes de la instalaciónPrueba uno de la puerta Prueba dos de la puertaHerramientas necesarias Características del sistemaLeer Y Seguir Todas LAS Instrucciones DE Instalación Tabla de materiasTransmisión Montaje del accionador en el rielInstalación Travesaño y cerrar la puerta Del garajeFrontal PuertaPosicionamiento del extremo Motor del accionador Fijar la unidad en el soporte De pared frontalDel accionador Montaje del extremoApropiado Para LA Puerta Montaje de soporte de puertaOperación Instalación de iluminaciónApropiado CON EL Interruptor LA Estación DE Pared Fuera DELDE Garaje Causar EL Malfuncionamiento DEL AccionadorLA Puerta DE Garaje Adhesivo no funciona Instalación de la estaciónEtiqueta de advertencia Sobre aprisionamientoArandela De seguridad, cableadoInstalación de sensor infrarrojo Herramientas necesariasSeguridad cableado al accionador Instalación de cableadoConexión del sensor infrarrojo de Conjunto del pestillo Conexión del accionadorAl tomacorriente Conexión del trole alCompletamente Cerrada Alineación de los sensoresLesiones Personales Desplace Hasta LA PosiciónMóvil DE LA Puerta Configuración de la posiciónCerrada del trole 10 a Conexión de brazoPara puerta a puerta Modelos 9700 yDe apertura de la puerta Calibración de recorridoDe cierre de la puerta Calibración del recorridoPerno de tope Trole Accionador Causar Lesiones Graves O Fatales Prueba de obstrucciónPor contacto Prueba de obstrucción Del sensor de seguridadPosibles Lesiones Personales Programación del accesoInalámbrico sin llave HerramientasEn otros materiales Instalación del accesoUbicación de cada tornillo GarajeIlustradas Conexión eléctrica opción de Cableado permanentePara LA Sección Superior CON Barra U Montaje de soporte de puerta Una puerta SerieInstalaciones Opcionales Taladro eléctrico Vástago de cubo De 7/16˝Presión Montaje del soporte de puerta a unaContinuar con el Paso Mordazas deDel brazo de la puerta De cierre del trole / ConexiónConexión Opcional Franqueo Superior ReducidoEn la página Configuración de la posición deCierre del trole / Conexión del El trole y reinstalar la chaveta hendidaRiel con franqueo Superior reducido Brazo curvo CON Franqueo Superior ReducidoParte inferior Del accionadorCómo Funciona LA LUZ Y QUÉ Significa Cuando Destella Leer Y Seguir Todas LAS InstruccionesJamás Ubicarse Bajo UNA Puerta PARADA, Parcialmente Abierta Activación de la puertaOperación de la estación inalámbrica de pared Comenzar con la puerta en la posición cerrada Personalización de la configuraciónControles del accionador Posición personalizada para mascotasProgramación primaria de HomeLink para Prodrive Programación alternativa de HomeLink para Prodrive Ajuste DE LA Fuerza DE Apertura AjustesAjuste DE LA Fuerza DE Cierre Estación DE Pared TransmisorTransmisor Cambio de pilas para la estación de pared MantenimientoDos veces al año Síntoma Causa Probable Acción Correctiva  Diagnóstico y resolución de problemasMantenimiento / Diagnóstico Y Resolución DE Problemas 309960 Conjunto de pestillo para cadena 18b 325687 Pieza Nro. porNro Descripción Unidad Nro. por unidadAcceso inalámbrico sin llave de 5 botones Transitorias MOV 252993 Interruptor de límites 311365Juego de sensor infrarrojo de seguridad Cordón de suministro eléctricoAcceso inalámbrico Accesorios del ProdriveDe operación a radiofrecuencia Para instalación en paredPre-drill 3/32 pilot hole Pre-drill 5/64 pilot holePlantilla DE Perforación Plantilla recortable para ayudar en la instalaciónGracias por su compra Cualquier pregunta y/o enviarán cualquier pieza necesariaGarantía Limitada DE POR Vida Información normativa de la FCC Información sobre patentesDeclaración de la FCC e IC

3324B-Z specifications

Wayne-Dalton is renowned for its commitment to innovative door solutions, and the Wayne-Dalton 3324B-Z is a prime example of their cutting-edge offerings in the realm of garage doors. This model is designed for residential settings, combining aesthetics with functionality.

One of the standout features of the 3324B-Z is its construction. The door is made from high-quality steel, ensuring exceptional durability and resistance to external elements. This steel is reinforced to provide strength and support, which is critical for maintaining the stability of the door over time. Moreover, the door is insulated with polyurethane, offering enhanced thermal efficiency. This insulation not only helps to regulate temperature within the garage but also contributes to energy savings by reducing heating and cooling costs.

Aesthetic appeal is another hallmark of the Wayne-Dalton 3324B-Z. Featuring a contemporary design, it is available in multiple color options and finishes, allowing homeowners to customize the look of their home while enhancing curb appeal. The door's design includes raised panel sections that add depth and texture, making it visually appealing without compromising on functionality.

In terms of technology, the Wayne-Dalton 3324B-Z integrates various advancements to enhance user experience and safety. It is equipped with a reliable spring system that promotes smooth operation and extends the lifespan of the door. The door can also be paired with Wayne-Dalton's innovative Quantum garage door opener, which features advanced security and remote access capabilities, allowing homeowners to operate their doors from anywhere via a smartphone app.

Safety is a paramount consideration in the design of the 3324B-Z. The door incorporates features such as pinch-resistant design, reinforced hinges, and safety sensors to protect users and pets from potential accidents during operation.

Installation and maintenance are also simplified with the Wayne-Dalton 3324B-Z. The door comes with detailed instructions for easy setup, and its durable materials require minimal upkeep, ensuring a long-lasting performance with minimal hassle.

In conclusion, the Wayne-Dalton 3324B-Z is a sophisticated choice for any homeowner seeking a balance of style, durability, and advanced technology. Its robust construction, attractive design, and safety features make it an ideal addition to modern homes. Whether upgrading an existing garage door or installing a new one, the 3324B-Z is a solution that stands out in functionality and aesthetics.
Top Page Image Contents