Wayne-Dalton 3324B-Z Wired Infrared Safety Sensor Installation, Wall Mounting Bracket Door Jam

Page 15

11

Tools Needed:

Ratchet Wrench

Tape Measure

Power Drill

3/16” Drill Bit

7/16” Socket

Driver

7/16” Wrench

Pencil

Wired Infrared Safety Sensor

Installation

IMPORTANT: BOTH WALL BRACKETS MUST BE MOUNTED AT THE SAME HEIGHT FOR PROPER ALIGNMENT.

Note: Use Steps a-c for installing sensors on both sides of the garage door.

a. Select and mark with a pencil, a mounting location no more than

5 inches above the floor to center line of wall mounting bracket. The safety sensors should be mounted as close to the door track or inside edge of the door as possible to offer maximum entrapment protection. It is very important that both wall mounting brackets be mounted at the same height for proper alignment.

b. Drill pilot holes, using a 3/16” drill bit. Using two 5/16” x 1-1/2” lag screws, permanently mount the wall mounting brackets to both door jambs. In some installations it may be necessary to attach a wooden spacer to the wall to achieve the required alignment.

Wall Mounting Bracket

5”

a

 

 

b

Door Jam

 

 

 

5/16” x 1-1/2”

 

Wall Mounting

Lag Screw

 

 

 

Bracket

 

 

Nut

 

Attach the “U” brackets to the wall mounting brackets with 1/4”-20 x 1/2” carriage bolts, washers and nuts. Insert the bolts from the inside of the “U” bracket and hand-tighten.

IMPORTANT: IDENTIFY WHICH SIDE OF THE GARAGE DOOR IS EXPOSED TO THE MOST SUNLIGHT. MOUNT THE SENDING UNIT (UNIT WITHOUT LED) ON THE SIDE WHICH IS EXPOSED TO THE MOST SUN. SUNLIGHT MAY AFFECT THE SAFETY SENSORS, AND THIS ORIENTATION WILL HELP REDUCE THE EFFECT.

c. Attach the sending and receiving safety sensors to the “U” brackets by inserting all three tabs into the respective holes.

Washer

1/4”-20 x 1/2” Carriage Bolt

c

U-Bracket

Receiving

LED

Unit

 

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 9 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Important Notice Garage Doors & OpenersNew 9/18/2008 Package Contents Page Door Test Two Pre-InstallationDisconnect from power source and proceed to assembly Door Test OneSystem Features Tools NeededHomelink Compatibility Rolling Code Technology Definition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationPositioning and Installing Front Wall Bracket Service PersonReinforce the Header Wall AT Least 3 Feet Long Positioning MotorEnd of Opener Attach Unit to Front Wall BracketMounting Opener End Proper InstallationReinforcing of Your Door Installing LightMounting Door Bracket Manufacturer for ProperGarage Door Wired Wall Station Installation If IncludedDoor can be Seen When Wall Station Near or Next toChildren and in a Location Where Wall Station Installation If IncludedWall Station Near or Next to Garage Door Wall Station OUT of the ReachConvenient location next to the wall station EntrapmentApply entrapment warning label in a Not adhereWasher Wired Infrared Safety Sensor InstallationWall Mounting Bracket Door Jam NutSensor to Opener Installation of Wiring for WiredInfrared Safety Sensor Connecting Wired Infrared SafetyCord in Anyway Connecting OpenerConnecting Trolley To Latch AssemblyFully Closed Position Alignment of Wired InfraredSafety Sensors Be Closed by ContinuouslySetting Trolley Close Position ARMTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Fatal Injury MAY Result Contact Obstruction TestTo Prevent Door Damage or Programming Wireless KeylessEntry If Included Possible Personal InjuryMaterials Important Install ALL WallWood framing using the two screws Surface inside garageInstructions Illustrated Power ConnectionTo Avoid Electrical Shock Important Check Your Local14 x 5/8 self tapping screws as shown in FIG Optional InstallationsTools Needed Power Drill Socket Driver Mounting Door Bracket To Series DoorShown in FIG Must be Adjusted ProperlyImportant When Connecting a BARLOW Headroom Radius Being UsedTrack For Portland TrackDIM Type of ARM Connecting Door ArmDetermine the WAYNE-DALTON Track Radius Being Used 15-18 LOW Headroom Trolley Positioning Chart forOptional Hookup LOW Headroom TrolleyDoor activation HOW the Light Works and What IT Means When IT FlashesOperation Read and Follow ALL InstructionsOperating the Wireless Wall Station Customizing the Settings Opener ControlsUp/Down Button Primary Programming for HomeLink to the Prodrive Programming/Training HomeLink UnitTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Opening Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Closing Force AdjustmentLarge Button Tools Needed NoneTransmitter Wall StationMaintenance Battery Replacement for Wall StationTwice a Year  Troubleshooting MAINTENANCE/ TroubleshootingSymptom Probable Cause Corrective Action Description # Per Unit Parts Breakdown Rail Assembly All Models2524 Parts Breakdown Opener Assembly And Accessories All ModelsProdrive Accessories Wireless Keyless Entry80ft gauge, 2 conductor polarized. UL listed CL-2, 75deg. C Multifunction Button Pre-drill 3/32 pilot holeDrill Template Pre-drill 5/64 pilot holeThank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent InformationPieza nro ¡AVISO ImportanteContenido del paquete Page Costado derecho del accionador Antes de la instalaciónPrueba uno de la puerta Prueba dos de la puertaHerramientas necesarias Características del sistemaLeer Y Seguir Todas LAS Instrucciones DE Instalación Tabla de materiasMontaje del accionador en el riel InstalaciónTransmisión Travesaño y cerrar la puerta Del garajeFrontal PuertaPosicionamiento del extremo Motor del accionador Fijar la unidad en el soporte De pared frontalDel accionador Montaje del extremoApropiado Para LA Puerta Montaje de soporte de puertaOperación Instalación de iluminaciónApropiado CON EL Interruptor LA Estación DE Pared Fuera DELDE Garaje Causar EL Malfuncionamiento DEL AccionadorLA Puerta DE Garaje Adhesivo no funciona Instalación de la estaciónEtiqueta de advertencia Sobre aprisionamientoArandela De seguridad, cableadoInstalación de sensor infrarrojo Herramientas necesariasInstalación de cableado Conexión del sensor infrarrojo deSeguridad cableado al accionador Conjunto del pestillo Conexión del accionadorAl tomacorriente Conexión del trole alCompletamente Cerrada Alineación de los sensoresLesiones Personales Desplace Hasta LA PosiciónConfiguración de la posición Cerrada del troleMóvil DE LA Puerta 10 a Conexión de brazoPara puerta a puerta Modelos 9700 yDe apertura de la puerta Calibración de recorridoDe cierre de la puerta Calibración del recorridoPerno de tope Trole Accionador Causar Lesiones Graves O Fatales Prueba de obstrucciónPor contacto Prueba de obstrucción Del sensor de seguridadPosibles Lesiones Personales Programación del accesoInalámbrico sin llave HerramientasEn otros materiales Instalación del accesoUbicación de cada tornillo GarajeIlustradas Conexión eléctrica opción de Cableado permanentePara LA Sección Superior CON Barra U Montaje de soporte de puerta Una puerta SerieInstalaciones Opcionales Taladro eléctrico Vástago de cubo De 7/16˝Presión Montaje del soporte de puerta a unaContinuar con el Paso Mordazas deDel brazo de la puerta De cierre del trole / ConexiónConexión Opcional Franqueo Superior ReducidoEn la página Configuración de la posición deCierre del trole / Conexión del El trole y reinstalar la chaveta hendidaRiel con franqueo Superior reducido Brazo curvo CON Franqueo Superior ReducidoParte inferior Del accionadorCómo Funciona LA LUZ Y QUÉ Significa Cuando Destella Leer Y Seguir Todas LAS InstruccionesJamás Ubicarse Bajo UNA Puerta PARADA, Parcialmente Abierta Activación de la puertaOperación de la estación inalámbrica de pared Comenzar con la puerta en la posición cerrada Personalización de la configuraciónControles del accionador Posición personalizada para mascotasProgramación primaria de HomeLink para Prodrive Programación alternativa de HomeLink para Prodrive Ajustes Ajuste DE LA Fuerza DE CierreAjuste DE LA Fuerza DE Apertura Transmisor TransmisorEstación DE Pared Mantenimiento Dos veces al añoCambio de pilas para la estación de pared  Diagnóstico y resolución de problemas Mantenimiento / Diagnóstico Y Resolución DE ProblemasSíntoma Causa Probable Acción Correctiva 309960 Conjunto de pestillo para cadena 18b 325687 Pieza Nro. porNro Descripción Unidad Nro. por unidadAcceso inalámbrico sin llave de 5 botones Transitorias MOV 252993 Interruptor de límites 311365Juego de sensor infrarrojo de seguridad Cordón de suministro eléctricoAcceso inalámbrico Accesorios del ProdriveDe operación a radiofrecuencia Para instalación en paredPre-drill 3/32 pilot hole Pre-drill 5/64 pilot holePlantilla DE Perforación Plantilla recortable para ayudar en la instalaciónGracias por su compra Cualquier pregunta y/o enviarán cualquier pieza necesariaGarantía Limitada DE POR Vida Información sobre patentes Declaración de la FCC e ICInformación normativa de la FCC

3324B-Z specifications

Wayne-Dalton is renowned for its commitment to innovative door solutions, and the Wayne-Dalton 3324B-Z is a prime example of their cutting-edge offerings in the realm of garage doors. This model is designed for residential settings, combining aesthetics with functionality.

One of the standout features of the 3324B-Z is its construction. The door is made from high-quality steel, ensuring exceptional durability and resistance to external elements. This steel is reinforced to provide strength and support, which is critical for maintaining the stability of the door over time. Moreover, the door is insulated with polyurethane, offering enhanced thermal efficiency. This insulation not only helps to regulate temperature within the garage but also contributes to energy savings by reducing heating and cooling costs.

Aesthetic appeal is another hallmark of the Wayne-Dalton 3324B-Z. Featuring a contemporary design, it is available in multiple color options and finishes, allowing homeowners to customize the look of their home while enhancing curb appeal. The door's design includes raised panel sections that add depth and texture, making it visually appealing without compromising on functionality.

In terms of technology, the Wayne-Dalton 3324B-Z integrates various advancements to enhance user experience and safety. It is equipped with a reliable spring system that promotes smooth operation and extends the lifespan of the door. The door can also be paired with Wayne-Dalton's innovative Quantum garage door opener, which features advanced security and remote access capabilities, allowing homeowners to operate their doors from anywhere via a smartphone app.

Safety is a paramount consideration in the design of the 3324B-Z. The door incorporates features such as pinch-resistant design, reinforced hinges, and safety sensors to protect users and pets from potential accidents during operation.

Installation and maintenance are also simplified with the Wayne-Dalton 3324B-Z. The door comes with detailed instructions for easy setup, and its durable materials require minimal upkeep, ensuring a long-lasting performance with minimal hassle.

In conclusion, the Wayne-Dalton 3324B-Z is a sophisticated choice for any homeowner seeking a balance of style, durability, and advanced technology. Its robust construction, attractive design, and safety features make it an ideal addition to modern homes. Whether upgrading an existing garage door or installing a new one, the 3324B-Z is a solution that stands out in functionality and aesthetics.
Top Page Image Contents