Wayne-Dalton 3324B-Z installation instructions Determine the WAYNE-DALTON Track Radius Being Used

I	Setting Trolley Close Position/			Horizontal
	Connecting Door Arm			Track
	(Models 9100, 9400, 9600, 5120, 5140 & 9700)				12” OR 15”		Horizontal
							Track
		With Torsion Springs
Tools Needed:	DETERMINE THE WAYNE-DALTON				FIG. 1
	TRACK RADIUS BEING USED:
								12”	FIG. 1.1
Needle Nose Pliers	FOR MOUNT HOPE AND PENSACOLA				TOP VIEW
	TRACK:			Clevis Pin	Trolley				Stamped
									Radius
Adjustable Wrench	Measure the curved ends of the horizontal
								12”
	track to determine if you have a 12” or 15”
	radius horizontal track, as shown in FIG. 1.
Ratchet Wrench	FOR PORTLAND TRACK:
7/16” Socket	The horizontal tracks are stamped with
	radius on the side of the horizontal track, as			Hairpin Cotter
9/16” Socket	shown in FIG. 1.1.
	NOTE: If necessary, remove the upper arm
Hacksaw	(straight arm) from the trolley, to use the				“X”
	lower arm (curved arm). Remove the hairpin
	cotter from the clevis pin at the front of
	trolley and slide clevis pin out far enough
	to slide the upper arm out between the left
	and right side of trolley body. Position the
	lower door arm so the end with the single
	hole lines up with the clevis pin. Slide clevis
	pin completely back into trolley and reinstall
	hairpin cotter.							10”, 12”, 14”, OR 15”
	LOW HEADROOM:							Standard Lift Track
	If you have low headroom track, as shown
	in FIG. 1.5 on page 26, then proceed with					Top Section
	“Low Headroom Trolley Positioning Charts”
	on page 26.
	STANDARD LIFT:						FIG. 1.2
	Using the STANDARD LIFT TROLLEY
	POSITIONING CHARTS, refer to DIM “X”
	to set the distance from header to trolley, as							Straight Arm
	shown in FIG. 1.2.						Curved
	NOTE: Depending on your setup, you may						Arm
	have to cut straight arm to accomplish
	trolley settings.
	STANDARD LIFT TROLLEY POSITIONING							Cut Straight Arm To
	CHART FOR 10” AND 12” RADIUS
								Accomplish Trolley
	FOR (MODELS 9100, 9400, 9600, 5120 & 5140)							Setting
	DIM “X”	TYPE OF ARM	REFERENCE				FIG. 1.3
		BEING USED	ILLUSTRATIONS
	11 1/2”-13”	STRAIGHT /	FIG. 1.3		STANDARD LIFT TROLLEY POSITIONING CHART
							FOR 14” AND 15” RADIUS
		CURVED
					(MODELS 9100, 9400, 9600, 5120 & 5140)
	If adjustment of the trolley position is				DIM “X”		TYPE OF ARM	REFERENCE
	required, use the close travel adjustment						BEING USED	ILLUSTRATIONS
	screw located on the bottom of the opener,						STRAIGHT /
	as shown in FIG 1.4 on page 26. A 1/4				10”-12”			FIG. 1.3
							CURVED
	turn equals approximately 1” of trolley
	travel; turn clockwise to decrease distance
	(forward) and counter-clockwise to increase				STANDARD LIFT TROLLEY POSITIONING CHART
	distance (forward).				FOR (MODEL 9700) 15” RADIUS
	NOTE: Proceed with “Connecting Door Arm				DIM “X”		TYPE OF ARM	REFERENCE
							BEING USED	ILLUSTRATIONS
	To Door” Step 18, on page 14.
					11 1/16”-		STRAIGHT /
								FIG. 1.3
					16 7/8”		CURVED

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 25 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com