Wayne-Dalton 3324B-Z installation instructions Primary Programming for HomeLink to the Prodrive

Page 36

I

Primary Programming for HomeLink® to the Prodrive ®

NOTE: This step can only be done on automobiles equipped with the HomeLink® System.

NOTE: Programming HomeLink® requires a Wayne-Dalton Transmitter that is programmed to the opener (the wallstation and transmitter(s) supplied with the opener, come pre-programmed from the factory). Any additional wallstation(s) or transmitter(s) will need to be programmed to the opener, see page 33.

IMPORTANT: Use the programming instructions provided with your vehicle first. Follow these instructions if the HomeLink® unit does not learn the transmitter, when using the vehicle’s instructions.

NOTE: If Primary Programming does not work then use the Alternate Procedure on next page.

NOTE: Vehicle may need to be in accessory position when programming. Check car owner’s manual.

NOTE: HomeLink® is a registered trademark of Johnson Controls.

Programming/Training HomeLink® Unit

WARNING

GARAGE DOOR MAY OPERATE DURING PROGRAMMING. TO AVOID POSSIBLE SEVERE OR FATAL INJURY, PLACE THE EMERGENCY DISCONNECT HANDLE IN THE MANUAL OPERATED POSITION.

1.Pull the manual disconnect to put the opener in the disengaged position.

2.Verify the HomeLink® unit has an empty channel press the desired HomeLink® button and observe the indicator light if it flashes slowly, the channel is empty and ready for programming. If pressing the desired channel/button causes the indicator light to blink rapidly, or come on without blinking this channel is already programmed. You either need to choose a different channel/button on the HomeLink®, or perform Step 3 below.

3.OPTIONAL – To completely clear all channels on the HomeLink® unit, press and hold the two outside buttons on the HomeLink® unit until the HomeLink® indicator light begins to flash rapidly (approx. 20 seconds), then release both buttons. (Do not perform this step to train additional hand-held transmitters.) NOTE: This operation erases all previously learned transmitters and you will need to re-teach any other transmitters to your HomeLink® unit.

4.Hold the end of the Wayne-Dalton hand-held transmitter approximately 1 to 3 inches away from the HomeLink® surface keeping the HomeLink® indicator light in view.

5.Simultaneously press and hold the Wayne Dalton transmitter large button and desired button on the HomeLink® module, continue to hold both buttons. In less than 10 seconds the LED on the HomeLink® module will either go solid or give a single quick flash, release both buttons when either occur.

NOTE: If this procedure is unsuccessful perform Alternate procedure.

Teaching HomeLink® to the opener

6.Press and release the program switch on the opener. The red program status light on the opener and light will turn on and remain lit for one minute, indicating that it is ready to learn.

7.Press the HomeLink® button used in Step 5 above for 1 to 3 seconds. The program status light and convenience light on the opener will turn on and off three times indicating a successful learn.

8.Press the HomeLink® button once more to operate the door. The opener will activate and the trolley will travel towards open, the next activation will cause the trolley to travel to the closed position and reengage, subsequent operations will move the door.

30Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 36
Contents Important Notice Garage Doors & OpenersNew 9/18/2008 Package Contents Page Pre-Installation Disconnect from power source and proceed to assemblyDoor Test One Door Test TwoSystem Features Tools NeededHomelink Compatibility Rolling Code Technology Table of Contents Definition of key words used in this manualInstallation Attaching Opener to RailPositioning and Installing Front Wall Bracket Service PersonReinforce the Header Wall Positioning Motor End of OpenerAttach Unit to Front Wall Bracket AT Least 3 Feet LongProper Installation Mounting Opener EndInstalling Light Mounting Door BracketManufacturer for Proper Reinforcing of Your DoorWired Wall Station Installation If Included Door can be Seen WhenWall Station Near or Next to Garage DoorWall Station Installation If Included Wall Station Near or Next to Garage DoorWall Station OUT of the Reach Children and in a Location WhereEntrapment Apply entrapment warning label in aNot adhere Convenient location next to the wall stationWired Infrared Safety Sensor Installation Wall Mounting Bracket Door JamNut WasherInstallation of Wiring for Wired Infrared Safety SensorConnecting Wired Infrared Safety Sensor to OpenerConnecting Opener Connecting TrolleyTo Latch Assembly Cord in AnywayAlignment of Wired Infrared Safety SensorsBe Closed by Continuously Fully Closed PositionSetting Trolley Close Position ARMTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Close Travel Setting Door Opening TravelStop Bolt Trolley Opener Contact Obstruction Test Fatal Injury MAY ResultProgramming Wireless Keyless Entry If IncludedPossible Personal Injury To Prevent Door Damage orImportant Install ALL Wall Wood framing using the two screwsSurface inside garage MaterialsPower Connection To Avoid Electrical ShockImportant Check Your Local Instructions IllustratedOptional Installations Tools Needed Power Drill Socket DriverMounting Door Bracket To Series Door 14 x 5/8 self tapping screws as shown in FIGMust be Adjusted Properly Important When Connecting aBAR Shown in FIGRadius Being Used TrackFor Portland Track LOW HeadroomConnecting Door Arm DIM Type of ARMDetermine the WAYNE-DALTON Track Radius Being Used LOW Headroom Trolley Positioning Chart for Optional HookupLOW Headroom Trolley 15-18HOW the Light Works and What IT Means When IT Flashes OperationRead and Follow ALL Instructions Door activationOperating the Wireless Wall Station Customizing the Settings Opener ControlsUp/Down Button Primary Programming for HomeLink to the Prodrive Programming/Training HomeLink UnitTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Adjustments Adjustment # 1 Opening and Closing ForceClosing Force Adjustment Opening Force AdjustmentTools Needed None TransmitterWall Station Large ButtonMaintenance Battery Replacement for Wall StationTwice a Year  Troubleshooting MAINTENANCE/ TroubleshootingSymptom Probable Cause Corrective Action Parts Breakdown Rail Assembly All Models Description # Per UnitParts Breakdown Opener Assembly And Accessories All Models 2524Prodrive Accessories Wireless Keyless Entry80ft gauge, 2 conductor polarized. UL listed CL-2, 75deg. C Pre-drill 3/32 pilot hole Drill TemplatePre-drill 5/64 pilot hole Multifunction ButtonPlease Do Not Return This Product To The Store Thank you for your purchaseLifetime Limited Warranty Replacement laborPatent Information FCC and IC Statement¡AVISO Importante Pieza nroContenido del paquete Page Antes de la instalación Prueba uno de la puertaPrueba dos de la puerta Costado derecho del accionadorCaracterísticas del sistema Herramientas necesariasTabla de materias Leer Y Seguir Todas LAS Instrucciones DE InstalaciónMontaje del accionador en el riel InstalaciónTransmisión Del garaje FrontalPuerta Travesaño y cerrar la puertaFijar la unidad en el soporte De pared frontal Posicionamiento del extremo Motor del accionadorMontaje del extremo Del accionadorMontaje de soporte de puerta OperaciónInstalación de iluminación Apropiado Para LA PuertaLA Estación DE Pared Fuera DEL DE GarajeCausar EL Malfuncionamiento DEL Accionador Apropiado CON EL InterruptorLA Puerta DE Garaje Instalación de la estación Etiqueta de advertenciaSobre aprisionamiento Adhesivo no funcionaDe seguridad, cableado Instalación de sensor infrarrojoHerramientas necesarias ArandelaInstalación de cableado Conexión del sensor infrarrojo deSeguridad cableado al accionador Conexión del accionador Al tomacorrienteConexión del trole al Conjunto del pestilloAlineación de los sensores Lesiones PersonalesDesplace Hasta LA Posición Completamente CerradaConfiguración de la posición Cerrada del troleMóvil DE LA Puerta Conexión de brazo Para puerta a puertaModelos 9700 y 10 aCalibración de recorrido De cierre de la puertaCalibración del recorrido De apertura de la puertaPerno de tope Trole Accionador Prueba de obstrucción Por contactoPrueba de obstrucción Del sensor de seguridad Causar Lesiones Graves O FatalesProgramación del acceso Inalámbrico sin llaveHerramientas Posibles Lesiones PersonalesInstalación del acceso Ubicación de cada tornilloGaraje En otros materialesConexión eléctrica opción de Cableado permanente IlustradasMontaje de soporte de puerta Una puerta Serie Instalaciones OpcionalesTaladro eléctrico Vástago de cubo De 7/16˝ Para LA Sección Superior CON Barra UMontaje del soporte de puerta a una Continuar con el PasoMordazas de PresiónDe cierre del trole / Conexión Del brazo de la puertaFranqueo Superior Reducido Conexión OpcionalConfiguración de la posición de Cierre del trole / Conexión delEl trole y reinstalar la chaveta hendida En la páginaCON Franqueo Superior Reducido Parte inferiorDel accionador Riel con franqueo Superior reducido Brazo curvoLeer Y Seguir Todas LAS Instrucciones Jamás Ubicarse Bajo UNA Puerta PARADA, Parcialmente AbiertaActivación de la puerta Cómo Funciona LA LUZ Y QUÉ Significa Cuando DestellaOperación de la estación inalámbrica de pared Personalización de la configuración Controles del accionadorPosición personalizada para mascotas Comenzar con la puerta en la posición cerradaProgramación primaria de HomeLink para Prodrive Programación alternativa de HomeLink para Prodrive Ajustes Ajuste DE LA Fuerza DE CierreAjuste DE LA Fuerza DE Apertura Transmisor TransmisorEstación DE Pared Mantenimiento Dos veces al añoCambio de pilas para la estación de pared  Diagnóstico y resolución de problemas Mantenimiento / Diagnóstico Y Resolución DE ProblemasSíntoma Causa Probable Acción Correctiva Pieza Nro. por Nro Descripción UnidadNro. por unidad 309960 Conjunto de pestillo para cadena 18b 325687Transitorias MOV 252993 Interruptor de límites 311365 Juego de sensor infrarrojo de seguridadCordón de suministro eléctrico Acceso inalámbrico sin llave de 5 botonesAccesorios del Prodrive De operación a radiofrecuenciaPara instalación en pared Acceso inalámbricoPre-drill 5/64 pilot hole Plantilla DE PerforaciónPlantilla recortable para ayudar en la instalación Pre-drill 3/32 pilot holeCualquier pregunta y/o enviarán cualquier pieza necesaria Gracias por su compraGarantía Limitada DE POR Vida Información sobre patentes Declaración de la FCC e ICInformación normativa de la FCC

3324B-Z specifications

Wayne-Dalton is renowned for its commitment to innovative door solutions, and the Wayne-Dalton 3324B-Z is a prime example of their cutting-edge offerings in the realm of garage doors. This model is designed for residential settings, combining aesthetics with functionality.

One of the standout features of the 3324B-Z is its construction. The door is made from high-quality steel, ensuring exceptional durability and resistance to external elements. This steel is reinforced to provide strength and support, which is critical for maintaining the stability of the door over time. Moreover, the door is insulated with polyurethane, offering enhanced thermal efficiency. This insulation not only helps to regulate temperature within the garage but also contributes to energy savings by reducing heating and cooling costs.

Aesthetic appeal is another hallmark of the Wayne-Dalton 3324B-Z. Featuring a contemporary design, it is available in multiple color options and finishes, allowing homeowners to customize the look of their home while enhancing curb appeal. The door's design includes raised panel sections that add depth and texture, making it visually appealing without compromising on functionality.

In terms of technology, the Wayne-Dalton 3324B-Z integrates various advancements to enhance user experience and safety. It is equipped with a reliable spring system that promotes smooth operation and extends the lifespan of the door. The door can also be paired with Wayne-Dalton's innovative Quantum garage door opener, which features advanced security and remote access capabilities, allowing homeowners to operate their doors from anywhere via a smartphone app.

Safety is a paramount consideration in the design of the 3324B-Z. The door incorporates features such as pinch-resistant design, reinforced hinges, and safety sensors to protect users and pets from potential accidents during operation.

Installation and maintenance are also simplified with the Wayne-Dalton 3324B-Z. The door comes with detailed instructions for easy setup, and its durable materials require minimal upkeep, ensuring a long-lasting performance with minimal hassle.

In conclusion, the Wayne-Dalton 3324B-Z is a sophisticated choice for any homeowner seeking a balance of style, durability, and advanced technology. Its robust construction, attractive design, and safety features make it an ideal addition to modern homes. Whether upgrading an existing garage door or installing a new one, the 3324B-Z is a solution that stands out in functionality and aesthetics.