Wayne-Dalton 3324B-Z installation instructions Alternate Programming for HomeLink to the Prodrive

Page 37

I

Alternate Programming for HomeLink® to the Prodrive ®

NOTE: This Step can only be done on automobiles equipped with the HomeLink® System.

NOTE: Programming HomeLink® requires a Wayne-Dalton Transmitter that is programmed to the opener (the wallstation and transmitter(s) supplied with the opener, come pre-programmed from the factory). Any additional wallstation(s) or transmitter(s) will need to be programmed to the opener, see page 33.

IMPORTANT: Use the programming instructions provided with your vehicle first. Follow these instructions if the HomeLink® unit does not learn the transmitter, when using the vehicle’s instructions.

NOTE: Vehicle may need to be in accessory position when programming. Check car owner’s manual.

NOTE: HomeLink® is a registered trademark of Johnson Controls.

Programming/Training HomeLink® Unit

WARNING

GARAGE DOOR MAY OPERATE DURING PROGRAMMING. TO AVOID POSSIBLE SEVERE OR FATAL INJURY, PLACE THE EMERGENCY DISCONNECT HANDLE IN THE MANUAL OPERATED POSITION.

1.Pull the manual disconnect to put the opener in the disengaged position.

2.Press and hold the two outside buttons on the HomeLink® unit until the HomeLink® indicator light begins to flash rapidly (approx. 20 seconds), then release both buttons. (Do not perform this step to train additional hand-held transmitters.) NOTE: This operation erases all previously learned transmitters and that you need to re-teach any other transmitters to your HomeLink® unit by repeating steps 3 - 6 below.

3.Hold the end of the Wayne-Dalton hand-held transmitter approximately 1 to 3 inches away from the HomeLink® surface keeping the HomeLink® indicator light in view.

4.Use the large button on the Wayne Dalton transmitter. Simultaneously press and hold desired Homelink® button and the Wayne Dalton transmitter large button. Continue to press both buttons counting LED flashes on the HomeLink® module; between 50 to 60 LED flashes the LED will either come on solid or do one “quick flash”; when either of these occur release both Wayne Dalton transmitter and HomeLink® buttons.

Teaching HomeLink® to the opener

5.Press the program switch on the opener. The red program status light on the opener and light will turn on and remain lit for one minute, indicating that it is ready to learn.

6.Press the HomeLink® button used in Step 4 above for 1 to 3 seconds. The program status light on the opener will turn on and off three times indicating a successful learn.

7.Press the HomeLink® the opener will activate and the trolley will travel towards open, the next activation will cause the trolley to travel to the closed position and reengage, subsequent operations will move the door.

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 31 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Garage Doors & Openers Important NoticeNew 9/18/2008 Package Contents Page Disconnect from power source and proceed to assembly Pre-InstallationDoor Test One Door Test TwoTools Needed System FeaturesHomelink Compatibility Rolling Code Technology Definition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationService Person Positioning and Installing Front Wall BracketReinforce the Header Wall End of Opener Positioning MotorAttach Unit to Front Wall Bracket AT Least 3 Feet LongMounting Opener End Proper InstallationMounting Door Bracket Installing LightManufacturer for Proper Reinforcing of Your DoorDoor can be Seen When Wired Wall Station Installation If IncludedWall Station Near or Next to Garage DoorWall Station Near or Next to Garage Door Wall Station Installation If IncludedWall Station OUT of the Reach Children and in a Location WhereApply entrapment warning label in a EntrapmentNot adhere Convenient location next to the wall stationWall Mounting Bracket Door Jam Wired Infrared Safety Sensor InstallationNut WasherInfrared Safety Sensor Installation of Wiring for WiredConnecting Wired Infrared Safety Sensor to OpenerConnecting Trolley Connecting OpenerTo Latch Assembly Cord in AnywaySafety Sensors Alignment of Wired InfraredBe Closed by Continuously Fully Closed PositionARM Setting Trolley Close PositionTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Fatal Injury MAY Result Contact Obstruction TestEntry If Included Programming Wireless KeylessPossible Personal Injury To Prevent Door Damage orWood framing using the two screws Important Install ALL WallSurface inside garage MaterialsTo Avoid Electrical Shock Power ConnectionImportant Check Your Local Instructions IllustratedTools Needed Power Drill Socket Driver Optional InstallationsMounting Door Bracket To Series Door 14 x 5/8 self tapping screws as shown in FIGImportant When Connecting a Must be Adjusted ProperlyBAR Shown in FIGTrack Radius Being UsedFor Portland Track LOW HeadroomDIM Type of ARM Connecting Door ArmDetermine the WAYNE-DALTON Track Radius Being Used Optional Hookup LOW Headroom Trolley Positioning Chart forLOW Headroom Trolley 15-18Operation HOW the Light Works and What IT Means When IT FlashesRead and Follow ALL Instructions Door activationOperating the Wireless Wall Station Opener Controls Customizing the SettingsUp/Down Button Programming/Training HomeLink Unit Primary Programming for HomeLink to the ProdriveTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Adjustment # 1 Opening and Closing Force AdjustmentsClosing Force Adjustment Opening Force AdjustmentTransmitter Tools Needed NoneWall Station Large ButtonBattery Replacement for Wall Station MaintenanceTwice a Year MAINTENANCE/ Troubleshooting  TroubleshootingSymptom Probable Cause Corrective Action Description # Per Unit Parts Breakdown Rail Assembly All Models2524 Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive Accessories80ft gauge, 2 conductor polarized. UL listed CL-2, 75deg. C Drill Template Pre-drill 3/32 pilot holePre-drill 5/64 pilot hole Multifunction ButtonThank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent InformationPieza nro ¡AVISO ImportanteContenido del paquete Page Prueba uno de la puerta Antes de la instalaciónPrueba dos de la puerta Costado derecho del accionadorHerramientas necesarias Características del sistemaLeer Y Seguir Todas LAS Instrucciones DE Instalación Tabla de materiasInstalación Montaje del accionador en el rielTransmisión Frontal Del garajePuerta Travesaño y cerrar la puertaPosicionamiento del extremo Motor del accionador Fijar la unidad en el soporte De pared frontalDel accionador Montaje del extremoOperación Montaje de soporte de puertaInstalación de iluminación Apropiado Para LA PuertaDE Garaje LA Estación DE Pared Fuera DELCausar EL Malfuncionamiento DEL Accionador Apropiado CON EL InterruptorLA Puerta DE Garaje Etiqueta de advertencia Instalación de la estaciónSobre aprisionamiento Adhesivo no funcionaInstalación de sensor infrarrojo De seguridad, cableadoHerramientas necesarias ArandelaConexión del sensor infrarrojo de Instalación de cableadoSeguridad cableado al accionador Al tomacorriente Conexión del accionadorConexión del trole al Conjunto del pestilloLesiones Personales Alineación de los sensoresDesplace Hasta LA Posición Completamente CerradaCerrada del trole Configuración de la posiciónMóvil DE LA Puerta Para puerta a puerta Conexión de brazoModelos 9700 y 10 aDe cierre de la puerta Calibración de recorridoCalibración del recorrido De apertura de la puertaPerno de tope Trole Accionador Por contacto Prueba de obstrucciónPrueba de obstrucción Del sensor de seguridad Causar Lesiones Graves O FatalesInalámbrico sin llave Programación del accesoHerramientas Posibles Lesiones PersonalesUbicación de cada tornillo Instalación del accesoGaraje En otros materialesIlustradas Conexión eléctrica opción de Cableado permanenteInstalaciones Opcionales Montaje de soporte de puerta Una puerta SerieTaladro eléctrico Vástago de cubo De 7/16˝ Para LA Sección Superior CON Barra UContinuar con el Paso Montaje del soporte de puerta a unaMordazas de PresiónDel brazo de la puerta De cierre del trole / ConexiónConexión Opcional Franqueo Superior ReducidoCierre del trole / Conexión del Configuración de la posición deEl trole y reinstalar la chaveta hendida En la páginaParte inferior CON Franqueo Superior ReducidoDel accionador Riel con franqueo Superior reducido Brazo curvoJamás Ubicarse Bajo UNA Puerta PARADA, Parcialmente Abierta Leer Y Seguir Todas LAS InstruccionesActivación de la puerta Cómo Funciona LA LUZ Y QUÉ Significa Cuando DestellaOperación de la estación inalámbrica de pared Controles del accionador Personalización de la configuraciónPosición personalizada para mascotas Comenzar con la puerta en la posición cerradaProgramación primaria de HomeLink para Prodrive Programación alternativa de HomeLink para Prodrive Ajuste DE LA Fuerza DE Cierre AjustesAjuste DE LA Fuerza DE Apertura Transmisor TransmisorEstación DE Pared Dos veces al año MantenimientoCambio de pilas para la estación de pared Mantenimiento / Diagnóstico Y Resolución DE Problemas  Diagnóstico y resolución de problemasSíntoma Causa Probable Acción Correctiva Nro Descripción Unidad Pieza Nro. porNro. por unidad 309960 Conjunto de pestillo para cadena 18b 325687Juego de sensor infrarrojo de seguridad Transitorias MOV 252993 Interruptor de límites 311365Cordón de suministro eléctrico Acceso inalámbrico sin llave de 5 botonesDe operación a radiofrecuencia Accesorios del ProdrivePara instalación en pared Acceso inalámbricoPlantilla DE Perforación Pre-drill 5/64 pilot holePlantilla recortable para ayudar en la instalación Pre-drill 3/32 pilot holeGracias por su compra Cualquier pregunta y/o enviarán cualquier pieza necesariaGarantía Limitada DE POR Vida Declaración de la FCC e IC Información sobre patentesInformación normativa de la FCC

3324B-Z specifications

Wayne-Dalton is renowned for its commitment to innovative door solutions, and the Wayne-Dalton 3324B-Z is a prime example of their cutting-edge offerings in the realm of garage doors. This model is designed for residential settings, combining aesthetics with functionality.

One of the standout features of the 3324B-Z is its construction. The door is made from high-quality steel, ensuring exceptional durability and resistance to external elements. This steel is reinforced to provide strength and support, which is critical for maintaining the stability of the door over time. Moreover, the door is insulated with polyurethane, offering enhanced thermal efficiency. This insulation not only helps to regulate temperature within the garage but also contributes to energy savings by reducing heating and cooling costs.

Aesthetic appeal is another hallmark of the Wayne-Dalton 3324B-Z. Featuring a contemporary design, it is available in multiple color options and finishes, allowing homeowners to customize the look of their home while enhancing curb appeal. The door's design includes raised panel sections that add depth and texture, making it visually appealing without compromising on functionality.

In terms of technology, the Wayne-Dalton 3324B-Z integrates various advancements to enhance user experience and safety. It is equipped with a reliable spring system that promotes smooth operation and extends the lifespan of the door. The door can also be paired with Wayne-Dalton's innovative Quantum garage door opener, which features advanced security and remote access capabilities, allowing homeowners to operate their doors from anywhere via a smartphone app.

Safety is a paramount consideration in the design of the 3324B-Z. The door incorporates features such as pinch-resistant design, reinforced hinges, and safety sensors to protect users and pets from potential accidents during operation.

Installation and maintenance are also simplified with the Wayne-Dalton 3324B-Z. The door comes with detailed instructions for easy setup, and its durable materials require minimal upkeep, ensuring a long-lasting performance with minimal hassle.

In conclusion, the Wayne-Dalton 3324B-Z is a sophisticated choice for any homeowner seeking a balance of style, durability, and advanced technology. Its robust construction, attractive design, and safety features make it an ideal addition to modern homes. Whether upgrading an existing garage door or installing a new one, the 3324B-Z is a solution that stands out in functionality and aesthetics.
Top Page Image Contents