Hearth and Home Technologies EDV3633L, EDV3633IL owner manual Mantel and Wall Projections

Page 21

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speciﬁed. Framing or ﬁnishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Mantels

Mantel Legs or Wall Projections

Note: All measurements in inches.

30 in. minimum

to ceiling

		18
		17
	15	16
14					20

				19-1/4

13		18-1/2
12	17-3/4

Top of

Appliance

A2 in. (51 mm) min. from fireplace opening to perpendicular wall

Drywall

A

Mantel Leg or Perpendicular Wall

										11				17
						9				10				16-1/4
										10				16-1/4
													15-1/2
													15-1/2
						8					14-3/4
						8					14-3/4
				6		7				14
						7				14
5								13-1/4
								13-1/4
							12-1/2
4						11-3/4
3				11
		10-1/4
	9-1/2
8-3/4

Measured from top of fireplace opening (in inches)

Figure 5.3 Minimum Vertical and Maximum Horizontal Dimensions

Figure 5.4 Mantel Leg or Wall Projections (Acceptable on both sides of opening)

Heatilator • Eclipse • 4049-229 Rev F • 11/08

21

Image 21

Contents Do not Discard this Manual What to do if you smell gasHomeowner Reference Information CongratulationsTable of Contents Installer GuideUser Guide Troubleshooting CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyWarranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsGas Fireplace Safety Operating InstructionsYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit Clear SpaceLighting Instructions For Your Safety Read Before Lighting After Fireplace is Lit Frequently Asked QuestionsMaintenance Tasks-Homeowner Maintenance and ServiceVenting Maintenance Tasks-Qualiﬁed Service TechnicianEither cobrahead or SIT Typical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseMantels Mantel Legs or Wall Projections Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsMinimum Clearances for Termination Approved Pipe Vent Information and DiagramsVent Table Key Use of ElbowsOne Elbow Vent DiagramsTop Vent Horizontal Termination Installed Vertically HorizontallyThree Elbows Top Vent Vertical Termination 12 ft 3.66 m min 60 ft 18.29 m max Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Installing Ceiling Firestop Install the Ceiling FirestopFlat Ceiling Installation Install Attic Insulation ShieldSecuring and Leveling the Appliance Appliance PreparationInstalling SLP Vent Pipe Assemble Vent SectionsAssemble Slip Sections Disassemble Vent Sections Securing the Vent SectionsInstalling Metal Roof Flashing SLP-FS Install RF4-8Assemble and Install Storm Collar Installing Vertical Termination CapInstall Heat Shields and Horizontal Termi- nation Cap Install Horizontal Termination Cap Fuel Conversion Gas InformationGas Pressure Gas ConnectionStanding Pilot Ignition System Wiring Wiring RequirementsIntelliﬁre Ignition System Wiring Optional Accessories RequirementsGAS Electrical Service and RepairWall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingRemove Glass Assembly Appliance SetupRemove Packaging Materials LogsInstall Floor Cover Replace GlassGrilles and Screen Accessories Air Shutter SettingStanding Pilot Ignition System TroubleshootingSymptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Will not ignite. If the pilot Reference Materials Appliance Dimension DiagramLength Vent Components DiagramsSLP-HRC-SS EDV3633 Service PartsEDV3633I, EDV3633IL Standing Pilot Valve Assembly Optional Components Contact Information