Hearth and Home Technologies EDV3633L, EDV3633IL owner manual Slp-Hrc-Ss

Page 55

B. Vent Components Diagrams (continued)

SLK-SNKD	SLP-TVHW
Snorkel	Vertical			PVK-80
Termination Cap	Termination Cap			Power Vent
	DVP-FBHT	SL-2DVP
	Horizontal Termination Cap	SL-2DVP
	Horizontal Termination Cap	Adapter
	(This termination cap requires	Adapter
	(This termination cap requires
	an SL-2DVP adapter when
	used with SLP Pipe)		8-1/8 in.	13 in.
			8-1/8 in.	13 in.
			(206 mm)	(330 mm)
	15 in.
	(381 mm)
SLP-TRAP1
Horizontal			SLP-HRC-SS
Termination Cap			SLP-HRC-SS
Termination Cap
	Effective Length	5-1/2 in.	8-3/8 in.
	5-3/4 to 8-3/8 in.	5-1/2 in.	8-3/8 in.
	146 to 213 mm	140 mm	213 mm
		87°	3°
		87°
			10-1/2 in.
			267 mm
			10-7/8 in.
			276 mm
SLP-TRAP2
Horizontal			SLP-HRC-ZC-SS
Termination Cap			SLP-HRC-ZC-SS
Termination Cap
Figure 16.3 SLP Series Vent Components
	Heatilator • Eclipse • 4049-229 Rev F • 11/08			55

Image 55

Contents Do not Discard this Manual What to do if you smell gasHomeowner Reference Information CongratulationsInstaller Guide Table of ContentsUser Guide Troubleshooting CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyWarranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsOperating Instructions Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan KitLighting Instructions For Your Safety Read Before Lighting After Fireplace is Lit Frequently Asked QuestionsMaintenance Tasks-Homeowner Maintenance and ServiceVenting Maintenance Tasks-Qualiﬁed Service TechnicianEither cobrahead or SIT Typical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseMantels Mantel Legs or Wall Projections Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsMinimum Clearances for Termination Use of Elbows Vent Information and DiagramsApproved Pipe Vent Table KeyOne Elbow Vent DiagramsTop Vent Horizontal Termination Installed Vertically HorizontallyThree Elbows Top Vent Vertical Termination 12 ft 3.66 m min 60 ft 18.29 m max Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Installing Ceiling Firestop Install the Ceiling FirestopFlat Ceiling Installation Install Attic Insulation ShieldSecuring and Leveling the Appliance Appliance PreparationAssemble Vent Sections Installing SLP Vent PipeAssemble Slip Sections Disassemble Vent Sections Securing the Vent SectionsInstalling Metal Roof Flashing SLP-FS Install RF4-8Assemble and Install Storm Collar Installing Vertical Termination CapInstall Heat Shields and Horizontal Termi- nation Cap Install Horizontal Termination Cap Gas Connection Gas InformationFuel Conversion Gas PressureOptional Accessories Requirements Wiring RequirementsStanding Pilot Ignition System Wiring Intelliﬁre Ignition System WiringGAS Electrical Service and RepairWall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingLogs Appliance SetupRemove Glass Assembly Remove Packaging MaterialsReplace Glass Install Floor CoverGrilles and Screen Accessories Air Shutter SettingStanding Pilot Ignition System TroubleshootingSymptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Will not ignite. If the pilot Reference Materials Appliance Dimension DiagramLength Vent Components DiagramsSLP-HRC-SS EDV3633 Service PartsEDV3633I, EDV3633IL Standing Pilot Valve Assembly Optional Components Contact Information