Elektra Beckum P 5500 M manual Equipment dismounting and storing, Trouble Shooting, Fault finding

Page 11

If the pump capacity lessens clean suction strainer and filter cartridge (if installed), replace if necessary.

7.2Danger of freezing

A Caution!

Frost damages the pump and accessories, as both always contain water!

When there is danger of freezing, dismount equipment and accesso- ries and store at a freeze-proof loca- tion (see below).

7.3Equipment dismounting and storing

1.Switch equipment OFF and unplug.

2.Open pressure line (open tap or spray nozzle) and drain water com- pletely.

3.Drain pump completely; to do so remove the drain plug from the pump

4.Disconnect suction and pressure lines from the equipment.

5.Store equipment in a frost-free space (at least 5 °C).

8.Trouble Shooting

ADanger!Prior to all servicing:

Switch Off.

Unplug.

Ensure that pressure is relieved from equipment and connected accessories.

8.1Fault finding

Pump does not run:

No mains voltage.

Check cables, plug, outlet and mains fuse.

Mains voltage too low.

Use only extension cables with sufficient lead cross section (see "Technical Specifications").

Motor overheated, motor protection relay tripped.

After cooling off the pump will switch ON again.

Ensure sufficient ventilation, keep vent slots clear.

Observe max. temperature of the pumped medium.

Motor hums but does not start.

With the motor switched OFF, put screwdriver or similar through the fan cover's vent slots and turn the fan.

Pump blocked or out of order.

Disassemble pump and clean.

Clean diffusor, replace if neces- sary.

Clean impeller, replace if neces- sary.

Pump does not prime correctly or runs very noisily:

Lack of water.

Ensure there is a sufficient water supply.

Suction line leaky.

Seal suction line, tighten screw fittings.

Suction head too high.

Observe max. suction head.

Install check valve, fill suction line with water.

Suction strainer (accessory) blocked.

Clean, replace if necessary.

Check valve (accessory) blocked.

Clean, replace if necessary.

Water leaks between motor and pump, Duocone seal worn.

Replace Duocone seal.

Pump blocked or out of order.

see above.

Pressure too low:

Suction line leaky or too much suc- tion head.

see above.

Pump blocked or out of order.

see above.

9. Repairs

ADanger!Repairs to electric tools must only be carried out by a qualified electrician!

Electric tools in need of repair can be sent to an authorised service center in your country. See spare parts list for address.

Please attach a description of the fault to the electric tool.

For shipping:

Drain pump completely (see "Equip- ment dismounting and storing").

Ship equipment in original packing, if possible.

10. Environmental Protection

The packaging of the pump can be 100 % recycled.

Worn out power tools and accessories contain considerable amounts of valua- ble raw and plastic materials, which can be recycled.

These instructions are printed on chlo- rine-free bleached paper.

ENGLISH

11. Available Accessories

For this equipment the following acces- sories are available at specialist dealers.

3 Note:

Illustrations and stock numbers can be found at the end of these instruc- tions.

APump Installation Package, complete with double nipple, check

valve, filter short, washable filter cartridge, spiral hose assembly 1 m, thread sealing tape.

BHydromat HM 1,

for automatic starting when water is drawn and stopping when no water is drawn, keeps the pump from run- ning dry.

CHydrostop,

for automatic stopping when there is a lack of water, prevents the pump from running dry.

DDry-running Stop Switch,

with 10 m cable, keeps the pump from running dry when pumping from tank, pool, etc.

ESpiral Hose 1"

1)1 m assembly, with quick release screw fitting at both ends;

2)4 m, complete with quick release screw fitting and strainer with foot valve;

3)7 m, complete with quick release screw fitting and strainer with foot valve.

FFilter, 1" connection, short, complete with washable plastic fil- ter cartridge.

GDisposable Filter Cartridge, short, for mechanical preliminary filtering of sand.

HWashable Filter cartridge, short, for mechanical preliminary filtering of sand, reusable.

IActivated Carbon Filter Cartridge, short,

for use with chlorous water, removes odours or discolouring.

JFilter Cartridge Poly, short,

filled with polyphosphate, for calcif- erous water supplied to water heat- ers.

KPipe Nipple 150 mm, 1" male at both ends, galvanized, to connect pump and filter.

LDouble Nipple, 1" male at boths ends.

MCheck Valve 1" female, prevents water backflow and pump running dry.

NThread Sealing Tape, 12 m roll.

11

Image 11
Contents 5500 M Pumpe Das Gerät im Überblick DeutschSicherheit Bestimmungsgemäße Verwendung InhaltsverzeichnisZuerst lesen Einsatzgebiet und För- dermedienBetrieb Druckleitung anschließenNetzanschluss Pumpe befüllen und AnsaugenBei Frostgefahr Probleme und StörungenWartung und Pflege Regelmäßige Wartung5500 M Technische DatenMachine Overview EnglishInstallation Table of ContentsSafety Specified conditions of use General safety instruc- tionsDischarge hose connec- tion Pump characteristic curveCare and Maintenance Periodic maintenanceEquipment dismounting and storing Trouble ShootingFault finding Available AccessoriesTechnical Specifications Vue densemble de lappareil FrançaisDomaine dutilisation et agents de transport Avant la mise en serviceTable des matières Lire en premierRaccordement au secteur Mise en service de lappareilRaccordement de la con- duite daspiration Raccordement de la con- duite sous pressionEn cas de risque de gel Maintenance et entretienMaintenance régulière Ligne caractéristique de la pompeCaractéristiques techniques Accessoires livrablesProtection de lenviron- nement Matériaux Boîtier de la pompe Het apparaat in een oogopslag NederlandsVeiligheid Voorgeschreven gebruik van het systeem InhoudstafelLees dit eerst Toepassingsgebied en pompmediaPomp vullen en aanzui- gen Aanzuigleiding aanslui- tenDrukleiding aansluiten NetaansluitingBij vorstgevaar Service en onderhoudProblemen en storingen Regelmatig onderhoudTechnische gegevens Gewichten Gewicht leeg Vista general del aparato EspañolSeguridad Utilización de acuerdo a su finalidad Indice del contenido¡Leer en primer lugar Campo de aplicación y líquidos a bombearLlenar la bomba y aspirar Conectar el conducto de aspiraciónConectar el conducto de presión Conexión a la redMantenimiento Problemas y averíasPoner en marcha el apa- rato Curva característica de la bombaAccesorios suministra- bles ReparaciónProtección ecológica Características técnicas Maskinen i overblik DanskGenerelle sikkerhedsan- visninger Læses førstAnvendelsesområde og medier Sikkerhed Korrekt anvendelseDrift Tilslut trykledningStrømtilslutning Fyldning af pumpe og indsugningFejlsøgning Problemer og forstyrrel- serVed risiko for frost Afmontering og opbeva- ring af apparatetTekniske Data Maskinens uppbyggnad SvenskaSäkerhet Använd maskinen enligt anvisningarna InnehållsförteckningLäs detta först Användningsområde och matarmediumIgångsättning Anslutning av tryckled- ningenNätanslutning Påfyllning av pumpen och uppsugningFelsökning FelsökningsschemaVid fara för frost Demontera pumpen för förvaringTekniska data Page Page 090 304 090 305 090 302 090 300 090 301 090 102 Achtung

P 5500 M specifications

The Elektra Beckum P 5500 M is a robust and versatile professional wood planer that has gained popularity among carpenters and woodworkers for its exceptional performance and reliability. Known for its high quality and precision, the P 5500 M is designed to meet the demanding needs of both professional users and serious hobbyists.

One of the standout features of the Elektra Beckum P 5500 M is its powerful motor. Equipped with a 2300-watt motor, this planer can easily handle a variety of wood types, delivering impressive cutting speeds and efficiency. The high torque output ensures that the machine can tackle thicker and denser materials without compromising on performance.

The P 5500 M features a cutting width of 500 mm, allowing users to process wider boards in a single pass. This significantly reduces the time and effort required for planing larger surfaces. The adjustable cutting depth, which can be finely tuned up to 3 mm, gives users precise control over the finish of the wood, allowing for smooth surfaces and consistent results.

Another notable aspect of the P 5500 M is its solid build quality. Constructed with a robust frame, it provides excellent stability during operation, minimizing vibration and ensuring accuracy. The heavy-duty design not only contributes to durability but also allows for prolonged use without the risk of wear and tear.

The planer is equipped with advanced technologies that enhance its usability. The spiral cutter head is a prime example, which provides a superior finish compared to traditional straight blades. This heads configuration minimizes tear-out while producing a smoother surface, making it ideal for high-quality woodworking projects. Moreover, the easy replacement of blades ensures that maintenance is straightforward and efficient, keeping downtime to a minimum.

Safety features are also a priority with the Elektra Beckum P 5500 M. The model includes a safety switch that prevents accidental start-ups, providing an added layer of security for users. Additionally, the transparent safety cover allows for easy monitoring of the cutting process while ensuring the operator’s safety.

In conclusion, the Elektra Beckum P 5500 M is a top-tier wood planer that combines power, precision, and durability. With its advanced features and reliable performance, it stands out as an essential tool for any serious woodworker or carpenter looking to achieve professional-quality finishes. Whether handling large projects or intricate detailing, the P 5500 M meets and exceeds expectations, making it a valuable addition to any workshop.