Bradley Brand Furniture WF3203, TBD3103 Adaptive infrared assembly for a drain and O drain units

Page 9

Installation

TDB3103, WF3203

5

Adaptive infrared assembly for A drain and O drain units

A INSTALL HEMMED END (NOT SHARP END) OF SUPPORT TUBE WITH GASKET ONTO BOWL (SEE FIGURE 7 ON PAGE 10).

B PLACE SPRAYHEAD WITH 3/8" TUBING ONTO SUPPORT TUBE AS SHOWN IN FIGURE 7 ON PAGE 10. RUN TUBING DOWN THROUGH SUPPORT TUBE. MAKE SURE SPRAY HOLES POINT AWAY FROM THE WALL.

PLACE UPPER TIE BAR (NOTCHED AT CORNERS OF BOTH ENDS) ON TOP OF SPRAYHEAD PARALLEL TO WALL. CONNECT THE C TWO THREADED TIE RODS TOGETHER USING THE COUPLING NUT WITH HEX HEAD SET SCREWS. RUN THE TIE ROD DOWN

THROUGH UPPER TIE BAR (SEE FIGURE 7) AND SECURE FROM UNDERNEATH THE BOWL USING THE LOWER TIE BAR (NO NOTCHES) AND HEX NUT WITH SOCKET HEAD SET SCREW. A MINIMUM OF 1-1/2" OF THREADED TIE ROD SHOULD PROTRUDE BELOW THE LOWER TIE BAR; THIS WILL BE REQUIRED TO ATTACH THE VALVING.

PLACE INFRARED MODULE ASSEMBLY ON TOP OF SPRAYHEAD. ROTATE UNTIL INFRARED MODULE LOCKS IN WITH TIE BAR. D DROP TWO INFRARED MODULE WIRES DOWN TO VALVE ASSEMBLY. MAKE SURE INFRARED MODULE WINDOWS ARE FACING

TOWARD THE FRONT OF THE UNIT.

NOTE! Skip to step E for units without soap.

FOR UNITS WITH SOAP OPTION, INSTALL THE SPACER, SOAP DISPENSER AND COVER USING THE COUPLING NUT, THIRD TIE ROD (8-5/8" LONG) AND SECOND COUPLING NUT AS SHOWN (SEE FIGURE 8 ON PAGE 11). SECURE WITH SPRAYHEAD RESTRAINING BRACKET, ACORN NUT AND SOCKET HEAD SCREW.

 

E SECURE INFRARED MODULE COVER AND TOP COVER WITH ACORN NUT AND SOCKET HEAD SET SCREW.

 

 

F

HOLDING THE VALVE ASSEMBLY OUTSIDE OF PEDESTAL, CONNECT 3/8" TUBING FROM SPRAYHEAD TO VALVE ASSEMBLY TUBE

 

CONNECTOR (SEE FIGURE 9A ON PAGE 12).

 

 

 

 

 

THREAD ONE SUPPLIED 3/8" NUT ONTO THE TIE ROD. SLIDE VALVE ASSEMBLY ON NEXT AND SECURE WITH ANOTHER 3/8" NUT.

 

SEE FIGURE 9A.

 

FOR A UNIT: CONNECT SUPPLY LINES TO STOPS USING SUITABLE FITTINGS.

G FOR O UNIT: INSTALL 1/2" NOMINAL COPPER TUBING SUPPLY LINES (PASS THEM THROUGH HOLES IN COVER DOWN THROUGH

 

SUPPORT COLUMN) AND CONNECT TO SUPPLY STOP VALVES USING SUITABLE FITTINGS.

 

 

6

Electrical connections for Adaptive Infrared

START-UP NOTE: Do not use for two minutes after making power connection. The sensors will take up to eight minutes (without being used) to adapt to the bowl if another object is detected during the two-minute start-up period.

A ATTACH INFRARED FEMALE CONNECT WIRE FROM INFRARED MODULE TO SOLENOID AS SHOWN IN FIGURE 9B ON PAGE 12.

B ATTACH THE INFRARED MALE CONNECT WIRE FROM THE INFRARED MODULE TO THE TRANSFORMER LEAD WIRE.

C ATTACH THE REMAINING TRANSFORMER LEAD WIRE TO THE SOLENOID.

D CONNECT 24 VAC TRANSFORMER PROVIDED TO POWER SOURCE.

E TURN SUPPLIES ON. OPEN CHECK/STOP VALVES COMPLETELY.

F OPEN VOLUME CONTROL VALVE COMPLETELY AND CHECK PIPING INSTALLATION FOR LEAKS.

G PASS YOUR HAND IN FRONT OF EACH SENSOR UNTIL AIR IS PURGED FROM THE LINES.

Bradley Corporation • 215-1332 Rev. T; EN 08-009

3-5-08

9

Image 9
Contents Commande à infrarouge Installation InstalaciónSupplies Required by Installer Table of ContentsPre-Installation Information Semi-Circular Washfountain Dimensions Semi-Circular Washfountain Dimensions Semi-Circular Washfountain Rough-Ins Rim Height Application AdjustmentRough-In Specifications Type a DrainType O Drain Rough-in drain & supplies Bowl/pedestal mounting and assemblySupply Stop Valve connection P-trap installation Installing drain spud in bowlElectrical connections for Adaptive Infrared Adaptive infrared assembly for a drain and O drain unitsShown Installation InstructionsRestraining TOP Cover Bracket Male Connect Female Connect Solenoid Valve Vernatherm Ajustment Instructions Cleaning/Maintenance Instructions for Terreon Cleaning/Maintenance Instructions for Gel-coated FiberglassSpecial Situations for Material Cleaning and Maintenance Instructions for Stainless Steel Soap Valve Lotion S09-057S Parts List Soap Valve Liquid S09-007S Parts ListValve Attaching Assembly AttachingParts List Soap Valve Powdered S09-010AQty Description Soap Maintenance Tips Problem Water splashes over the rim of the bowl Sprayhead Service SuggestionsProblem Water flow diminishes from the sprayhead Sprayhead Repair Kit Assembly S05-054BModule Assembly Components S50-367 Troubleshooting Adaptive IRIR Actuator Solenoid Valve Troubleshooting Solenoid Valve S07-069 closed body Thermostatic Mixing Valve Troubleshooting Problem Limited water flowProblem External leaks in the system Repair Kit S65-259 Informations sur la pré-installation Fournitures requises par l’installateurSommaire Matériau TerreonDimensions du lavabo fontaine semi-circulaire Directives dimensionnelles ADADe bord Application Ajustement Vue de dessus Hauteur de bord Application Ajustement Spécifications de mise en place des tuyauteries Drain de type aDrain de type O Montage de l’ensemble cuvette et socle Mise en place des tuyauteries de drain et d’alimentationCuvette Installation de l’ergot de drain dans laOpposé DU MUR Connexions électriques pour infrarouge AdaptiveIllustrée Instructions relatives à l’installation suiteCouvercle Console DE Supérieur Retenue Thermostatic Mixing Valve Illustré S45-2233 Instructions de réglage Vernatherm Situations spéciales de matériau Instructions de nettoyage/d’entretien pour TerreonSituations spéciales de matériau Bouton-poussoir de lotion savonneuse S09-057S Nomenclature Bouton-poussoir de savon liquide S09-007S NomenclatureFixation Repère Référence Désignation QtéBouton-poussoir de savon en poudre S09-010A NomenclatureRepère Référence Qté Désignation Conseils d’entretien pour le savon Suggestions pour réparer le bec diffuseur Problème L’eau éclabousse tout autour du bord de la cuvetteEnsemble bec Kit de réparation Diffuseur S05-054B Composants de l’ensemble de module I.R. S50-367 Dépannage IR AdaptiveActionneur IR Guide de dépannage du robinet électromagnétique Robinet électromagnétique S07-069 corps fermé Dépannage du robinet mélangeur thermostatique Problème Débit d’eau limitéProblème Fuites externes dans le système Kit de réparation S65-259 Robinet mélangeur thermostatique Vernatherm S01-524Índice Suministros requeridos por el instaladorInformación previa a la instalación Material TerreonDimensiones de ADA Dimensiones de la fuente de lavado semicircularVista en planta Altura del borde Aplicación Ajuste Figura 1cDesagüe tipo O Desagüe tipo aDesagüe y suministros empotrados Montaje y ensamblaje dePalangana/pedestal Palangana Instalación del embudo de desagüe en la¡NOTA! Vaya hasta el paso E para las unidades sin jabón Se muestra a Instrucciones de instalación continuaciónSoporte DE Cubierta Superior Contención Figura 9b Instrucciones de ajuste de Vernatherm Situaciones especiales del material Instrucciones de limpieza/mantenimiento de TerreonSituaciones especiales del material Válvula para jabón líquido S09-057S Lista de piezas Válvula para jabón líquido S09-007S Lista de piezasVálvula de jabón en polvo S09-010A Lista de piezasArticulo Nº de pieza Cant Descripción Consejos para el mantenimiento del jabón Problema El agua salpica sobre el borde de la palangana Sugerencias de reparaciones de la boquilla rociadoraConjunto de boquilla Equipo de Rociadora S05-054B Componentes del conjunto del módulo IR S50-367 Localización de fallas del dispositivo IR AdaptiveActuador IR Localización de fallas de la válvula de solenoide Válvula de solenoide S07-069 cuerpo cerrado Problema Fugas externas en el sistema Problema Flujo de agua limitadoEquipo de reparación S65-259 Válvula mezcladora termostática Vernatherm S01-524

TBD3103, WF3203 specifications

Bradley Brand Furniture, recognized for its commitment to quality and innovative design, has introduced two standout models: the WF3203 and the TBD3103. Both pieces exemplify the brand's dedication to creating functional yet stylish furniture for contemporary living spaces.

The WF3203 model is a versatile sofa that seamlessly marries comfort with modern aesthetics. It features a sleek silhouette characterized by clean lines and soft curves, making it an ideal addition to any living room. One of its main features is the high-density foam cushioning, which provides superior support while ensuring a plush seating experience. The upholstery is made from durable, easy-to-clean fabric, available in a variety of colors to suit diverse interior styles. Additionally, this model includes a modular design, allowing users to reconfigure the seating arrangement to meet their needs, whether it be for family gatherings or entertaining guests.

On the other hand, the TBD3103 is a multifunctional coffee table that captures attention with its unique design and practicality. This model showcases a combination of tempered glass and solid wood, providing a sophisticated yet stable surface for daily use. One of its standout characteristics is the integrated storage compartment, cleverly hidden beneath the tabletop, which allows homeowners to keep their living spaces organized without sacrificing style. The TBD3103 also features adjustable legs, enabling users to heighten or lower the table according to their preferences or room layout.

Both models are built with sustainability in mind, utilizing eco-friendly materials that ensure durability while minimizing environmental impact. The craftsmanship behind each piece reflects a meticulous attention to detail, ensuring that they can withstand the rigors of everyday life.

In terms of technology, both models are designed with user convenience in focus. The WF3203 includes built-in USB ports, allowing users to charge devices without leaving the comfort of the sofa. Meanwhile, the TBD3103 is compatible with smart home systems, enabling seamless integration into modern living environments.

In conclusion, the Bradley Brand Furniture WF3203 and TBD3103 embody the brand's philosophy of marrying form and function. With their stylish aesthetics, innovative features, and thoughtful design, these furniture pieces enhance the living experience, making them ideal choices for anyone looking to elevate their home decor.